Abstract:Powder metallurgy is an effective method to produce Cu-Al-based alloys for automotive and aerospace engineering components. The finer grain size, low cost, and low-temperature synthesis make this process more suitable than the other conventional production method such as melting and casting. The addition of Ni (austenite stabilizer) into the Cu increases the stability of Cu and refines the grain size. Again, the addition of Ni into the Cu-Al alloy increases the strength and hardness. In the present work, Cu-12Al alloys are developed by varying the wt.% of Ni content from 0 to 8 using powder metallurgy process through mechanical alloying method. Mechanical alloyed powder mixture is compacted by applying a load of 5 tons and sintered at 850 °C for 1 h under nitrogen atmosphere. It is found that α-Cu, γ2-Cu9Al4, and NiAl phases are presented in the Cu-12Al-Ni alloy which influences the properties of the alloy. The theoretical, sintered, and relative density values are decreased with increasing the wt.% of Ni content. However, the Vickers hardness of the alloy is improved by increasing the wt.% of Ni content up to 4 wt.% and then reduced for 8 wt.% of Ni content due to the coarsening and network-type structure of the NiAl phase. A higher amount of wear loss or wear rate is observed for the Cu-12Al and Cu-12Al-2Ni alloy than the Cu-12Al-4Ni and Cu-12Al-8Ni alloy. The presence of oxygen peaks in the EDS analysis revealed that an oxidative type of wear is occurred for the Cu-12Al alloy samples with varying the wt.% of Ni content. The electrochemical corrosion analysis revealed that the rate of corrosion is higher for Cu-12Al alloy without Ni. However, the rate of corrosion is reduced by increasing the wt.% of Ni content from 2 to 8.

Non-isothermal aging behavior of a friction-surfaced Al-Cu-Mg alloy matrix composite coating reinforced by nickel-aluminide

The Effect of Al on Microstructure and Properties of Cu-15Ni-8Sn During the Aging

Effect of friction surfacing parameters on the microstructural, mechanical properties, and wear characteristic of Al-Cu-Mg alloy coating reinforced by nickel aluminide

Effect of Non-isothermal Cooling Aging on the Microstructure and Properties of Al-Zn-Mg-Cu Alloys

Effect of aging treatment on microstructure and wear performance of Ni-rich NiTiFe alloy

Ageing Behavior and Stress Corrosion Cracking Resistance of a Non-Isothermally Aged Al–Zn–Mg–Cu Alloy

Study of Aging Temperature on the Thermal Compression Behaviors and Microstructure of a Novel Ni-Cr-Co-Based Superalloy

Microstructure and Mechanical Properties of Twin-Wire Arc Sprayed Ni-Al Composite Coatings on 6061-T6 Aluminum Alloy Sheet

The Influence of Cu Content on the Aging Behavior of Al 2 O 3 P / Al-Cu-Mg Composite

Enhancing Wear Resistance of CoNiCrMo Medium Entropy Alloy through Cold Working and Aging: Tradeoffs with Corrosion Performance

Effects of co-addition of Ni and Al on precipitation evolution and mechanical properties of Fe-Cu alloy

Effect of Non-Isothermal Aging on the Microstructure and Properties of Al-Zn-Mg-Cu Alloys

Nanoindentation and isothermal compression behaviour of Al–4Cu–Ni composites

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

Effects of Ni content on microstructure and wear behavior of Al–13Si–3Cu–1Mg-xNi-0.6Fe-0.6Mn alloys

Effects of Al Addition and Annealing on Microstructure and Properties of Ni-Ti Coatings Synthesized on SUS 316L Stainless Steel Substrates Using Mechanical Alloying Method

Effect of Non-Isothermal Aging on the Mechanical Properties and Corrosion Resistance of 2A12 Aluminum Alloy

Study of the high-temperature mechanical properties of Al-6061/NiTi reinforced metal matrix composites

Aging Behavior of Al 2 O 3 Short Fiber Reinforced Al-Cu Alloy Composites

The effect of nickel coating on the mechanical properties and failure modes of continuous carbon fiber reinforced aluminum matrix composites

Microstructure, Mechanical, and Tribological Relationship in Cu-12Al-Ni Alloy with Respect to the Variation of Ni Content