Abstract:The structure, phase composition, hardness, and tribological properties of composite gas-thermal 50% Cu–50% (Al–Si) coatings under various friction conditions were studied. It has been shown that during the process of high-speed metallization, active interaction of molten aluminum and copper particles occurs, leading to the formation of solid solutions and intermetallic compounds in sprayed coatings. In particular, in 50% Cu–50% (Al–Si) coatings, in addition to the matrix phases of Cu and Al, intermetallic compounds Cu 9 Al 4 , CuAl 2 , and Cu 3 Al are recorded. The hardness and microhardness of the composite are 180 HV 1 and 180–190 HV 0.025, respectively. It has been established that a composite coating of 50% Cu–50% (Al–Si) has higher wear resistance under various friction conditions than the widely used coating of CuSn11P-C antifriction bronze, obtained by centrifugal induction surfacing. In particular, in the environment of I-20A lubricant, the wear resistance of the composite coating exceeds the wear resistance of bronze by ≈1.2 times, in the environment of Litol-24 plastic lubricant, by ≈1.4 times, and with dry friction up to ≈2.8 times. It has been shown that during boundary friction, dislocations accumulate in aluminum particles of the composite, while in copper particles at elevated test pressures, a predominant formation of a subgrain structure occurs. Based on the studies conducted, it was concluded that the increased wear resistance of the composite is due to the presence of solid intermetallic compounds in it, solid solution strengthening, the presence of silicon in aluminum interlayers, as well as dislocation strengthening of aluminum interlayers and the formation of a subgrain structure in copper interlayers.

Effect of friction surfacing parameters on the microstructural, mechanical properties, and wear characteristic of Al-Cu-Mg alloy coating reinforced by nickel aluminide

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Wear Behaviour of Friction Surfaced Al-Ni and Al-SiC Coatings over Mild Steel

Non-isothermal aging behavior of a friction-surfaced Al-Cu-Mg alloy matrix composite coating reinforced by nickel-aluminide

Microstructure and Corrosion Study on Friction Surfaced Aluminum Alloy Coatings over Mild Steel

SURFACE PROPERTY CNHANCEMENT OF Al‐Si‐Cu ALLOY COATING BY FAST MULTIPLE ROTATION ROLLING

Effect of Cu/Ni coating on the interface and mechanical properties of C f /2024Al composites

Effect of initial heat treatment of A390 alloy on microstructure and tribological behavior of friction surfaced coating

Processing of Al–Si–Cu alloy coating using fast multiple rotation rolling

Substructural Changes in the Surface Layers of Composite Gas-Thermal Cu–(Al–Si) Coatings during Friction under Various Conditions

Tribological analysis and machine learning modeling of nickel-coated graphite reinforced A206 metal matrix composites

Effects of friction stir processing parameters on the wear resistance and mechanical properties of fabricated metal matrix nanocomposites (MMNCs) surface

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Microstructure and Wear Resistance of a Composite Coating Prepared by Laser Alloying with Ni-Coated Graphite on Ti-6Al-4V Alloy

Enhancing microstructural, tribological and corrosion responses of Al–Zn–Mg–Cu alloy via nano-/micro-Al2O3 particulates

Effects of Ni-5 wt% Al/Bi2O3 addition and heat treatment on mechanical and tribological properties of atmospheric plasma sprayed Al2O3 coating

Fabrication of Al6061/Ti 3 AlC 2 MAX phase surface composite by friction stir processing and investigation of wear properties

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Effect of Surface Roughness and Structure Features on Tribological Properties of Electrodeposited Nanocrystalline Ni and Ni/Al2O3 Coatings

Microstructure, Friction, And Wear Properties Of Ni-Al2o3-Mos2 Composite Coatings

Investigation of Friction and Wear Behavior of NiAl-based Alloys at Room Temperature