Abstract:Introduction: During severe plastic deformation (SPD) processing, aluminum alloys exhibit moderate strength and ductility. Nevertheless, the materials' ductility, as determined by tensile testing, does not accurately represent their capacity for plastic deformation. After the tensile test, its material, aluminum alloy 5083, was observed to be super ductile. Method: The results of a more thorough plasticity analysis—applied for the first time to material following SPD processing—are presented in this paper. The aluminum alloy 5083 is examined in the patent both before and after equal channel angular pressing (ECAP). A highly effective aluminum alloy 5083 specimen preparation was suggested. Under heated temperatures, the process involves severe plastic deformation. Optical microscopy and scanning electron microscopy (SEM) were used for micro-structural research in order to look at the distribution of second-phase particles and the evolution of grain structure. Furthermore, Vickers micro-hardness testing was utilized to assess the mechanical characteristics of the alloy after processing. The outcomes showed that after ECAP processing, there was a significant decrease in grain size and an increase in micro-hardness. Result: Additionally, the production of a finer microstructure with a more uniform distribution of strengthening precipitates was clarified by electron microscopy (SEM). The micro-structural evolution and mechanical behavior of aluminum alloy 5083 under ECAP are well-explained in this patent, which may lead to improved performance in structural applications. This method can be used to forecast fractures in plastic deformation processes and estimate the final plasticity of the materials for various stress-strain states after ECAP processing, as well as the mechanical properties discussed. Conclusion: Due to its unique mechanical qualities, aluminum alloy 5083 shows great potential in a variety of structural applications. The effects of Equal Channel Angular Pressing (ECAP) on the hardness and microstructure of aluminum alloy 5083 were examined in this patent work. result: The specimen's mechanical characteristics are at their finest following a single deformation when the temperature reaches 300°C. Compared to the original specimen, the tensile strength observed enhanced after the fourth pass, and breaking elongation (28.3%) was improved. Through second-phase strengthening and fine-tuning, the recrystallized grains and second-phase particles increase the material's strength.

Simultaneous improvement of mechanical strength and corrosion resistance in aluminum alloy 5083 via severe plastic deformation

Simultaneous improvement of corrosion and mechanical properties of AA 5083 aluminum alloy

Enhanced Microstructure Homogeneity and Mechanical Properties of AZ31 Magnesium Alloy by Repetitive Upsetting

Microstructure Evolution and Mechanical Properties of Az91d Magnesium Alloy Processed by Repetitive Upsetting

Improvement in corrosion resistance of 5083 aluminum alloy via friction stir processing

The Effects of Cold Rolling and Stabilization Treatment on the Improvement of Microstructure, Mechanical Properties, and Corrosion Behavior of AA5083 Sheet

Microstructural Evolution and Mechanical Properties of Multi-layered Aluminum Alloy 6061 Processed by Accumulative Roll Bonding

Corrosion Behavior of Ultra-fine Grained 1050 Aluminum Alloy Fabricated by ARB Process in a Buffer Borate Solution

Influence of Equal Channel Angular Pressing Technique on Mechanical Properties, Corrosion Resistance, and Microstructural Behavior of Al-Alloy 5083

Effect of Repeated Processing Passes during Ultrasonic Rolling on Fatigue Performance and Corrosion Resistance of Ti6Al4V Alloy

Electrochemical corrosion behavior of 7075 aluminum alloy with different ultrasonic surface rolling microstructures

Preparation of high performance 5083 aluminum alloy by alternate ring-groove pressing and torsion

On the microstructure and corrosion behavior of Fe-28.5Ni steel subjected to severe plastic deformation

Improving Mechanical and Corrosion Properties of 6061 Al Alloys via Differential Speed Rolling and Plasma Electrolytic Oxidation

Corrosion and mechanical properties of Al/Al 2 O 3 composites fabricated via accumulative roll bonding process: Experimental and numerical simulation

Microstructure and Mechanical Properties of AZ61 Magnesium Alloy Prepared by Repetitive Upsetting-Extrusion

Improving mechanical anisotropy and corrosion resistance of extruded AA7075 alloy by warm cross rolling and annealing

Cyclic Extrusion Compression Process for Achieving Ultrafine-Grained 5052 Aluminum Alloy with Eminent Strength and Wear Resistance

Simultaneously increased strength and plasticity of TIG-welded 7075-T6 aluminum alloy joints via a novel post-weld composite treatment process

Simultaneously improving tensile properties and stress corrosion cracking resistance of 7075-T6 aluminum alloy by USRP treatment

Effect of three-dimensional deformation at different temperatures on microstructure, strength, fracture toughness and corrosion resistance of 7A85 aluminum alloy