Abstract:The transesterification of cellulose with vinyl esters in ionic liquid media is suggested as a prospective environmentally friendly alternative to conventional esterification. In this study, various long-chain cellulose esters (laurate, myristate, palmitate, and stearate) with a degree of substitution (DS) up to 1.8 have been synthesized in novel distillable ionic liquid, [mTBNH][OAC]. This IL has high dissolving power towards cellulose, which can improve homogeneous transesterification. Additionally, [mTBNH][OAC] has durability towards recycling and can be regenerated and re-used again for the next cycles of esterification. DMSO is used as a co-solvent because of its ability to speed up mass transport due to lower solvent viscosity. The optimization of the reaction parameters, such as co-solvent content, temperature (20–80 °C), reaction time (1–5 h), and a molar ratio of reactants (1–5 eq. AGU) is reported. It was found that within studied reaction conditions, DS increases with increasing reaction time, temperature, and added vinyl esters. Structure analysis using FTIR, 1H, and 13C NMR after acylation revealed the introduction of the alkyl chains into cellulose for all studied samples. The results also suggested that the substitution order of the OH group is C7-O6 ˃ C7-O2 ˃ C7-O3. Unique, complex thermal and rheological investigation of the cellulose esters shows the growth of an amorphous phase upon the degree of substitution. At the same time, the homogeneous substitution of cellulose with acyl chains increases the melt viscosity of a material. Internal plasticization in cellulose esters was found to be the mechanism for the melt processing of the material. Long-chain cellulose esters show the potential to replace commonly used externally plasticized cellulose derivatives.

Efficient Conversion of Cellulose to Thermoplastics by Mechanochemical Esterification

One-Step Solvent-Free Strategy to Efficiently Synthesize High-Substitution Cellulose Esters

Insight into the Feasibility of Fatty Acyl Chlorides with 10-18 Carbons for the Ball-Milling Synthesis of Thermoplastic Cellulose Esters

Cellulose Modification by Recyclable Swelling Solvents

Direct One-step Synthesis of Cellulose Laurate Ester Via Mechanochemical Method

One-pot Conversion of Cellulose to HMF under Mild Conditions Through Decrystallization and Dehydration in Dimethyl Sulfoxide/tetraethylammonium Chloride

Mechanochemical preparation of thermoplastic cellulose oleate by ball milling

Efficient Preparation of All Cellulose Composite Films Using a Plasticizing-Rolling Method

Esterification of Cellulose with Long Fatty Acid Chain through Mechanochemical Method

Preparation of Thermoplastic Cellulose Esters in [mTBNH][OAC] Ionic Liquid by Transesterification Reaction

Homogeneous Transesterification of Sugar Cane Bagasse Toward Sustainable Plastics

Time and Energy-Efficient Homogeneous Transesterification of Cellulose under Mild Reaction Conditions

A Biodegradable, Waterproof, and Thermally Processable Cellulosic Bioplastic Enabled by Dynamic Covalent Modification

Sustainable conversion regenerated cellulose into cellulose oleate by sonochemistry

Defibrillation and functionalization of cellulose fibers from different sources in one-step via a mechanochemical method

Green Synthesis of Cellulose Formate and Its Efficient Conversion into 5-Hydroxymethylfurfural

Plasticized Cellulosic Films by Partial Esterification and Welding in Low-Concentration Ionic Liquid Electrolyte

A facile strategy towards heterogeneous preparation of thermoplastic cellulose grafted polyurethane from amorphous regenerated cellulose paste

A Novel Transesterification System to Rapidly Synthesize Cellulose Aliphatic Esters

“Three Birds with One Stone” Strategy for Building Easily Reprocessable Cellulosic Thermosetting Resins

Facile Preparation of Cellulose/Polylactide Composite Materials with Tunable Mechanical Properties