Abstract:In vessel retention (IVR) is one of the key severe accident mitigation strategies to maintain reactor pressure vessel (RPV) integrity. IVR designs utilize the reactor pressure vessel lower head to contain molten fuel and rely on external reactor vessel cooling (ERVC) to remove decay heat. The capacity of ERVC is limited by the critical heat flux (CHF) of flow boiling on the outside of the reactor vessel surface. Therefore, the determination of critical heat flux (CHF) is crucial to predict whether the adoption of IVR would be successful in mitigating severe accidents. In 1999, Celeta et.al proposed a superheated layer vapor replenishment model. In this model they postulated that CHF would occur when the superheated layer was occupied by the vapor blanket coming into contact with the heated wall and they successfully predicted the critical heat flux in subcooled water flow boiling under high mass flux, high liquid subcooling and low/medium pressure conditions. To evaluate the practicability of this model in predicting CHF under IVR conditions, CHF experiments were performed under natural circulation conditions on the experiment facility "Test of External Vessel Surface with Enhanced Cooling" (TESEC). Experiments are conducted in a 30 mm wide, 61mm high rectangular flow channel with a 200 mm long heated surface along the flow direction. Two quartz windows are installed at the sidewalls of the flow channel for visualization. In order to simulate various positions of the reactor lower head, experiments at different inclination angles of the test section were conducted. The high speed visualization data at CHF point at various inclination angles were processed and analyzed by a MATLAB code developed by the author. The vapor blanket thickness at various inclination angles was measured from the visualization data and was also predicted by the Celeta model. By using geometry data from high speed images, CHF values were calculated by Celeta model and compared with the experimental results at various inclination angles. Limitations of the Celeta model in adaptation of predicting CHF under IVR conditions were further discussed.

Experimental Investigation of the Heaving Motion Effect on Critical Heat Flux Phenomena and Wall Temperature Fluctuation Using R134a for Floating Nuclear Applications

Experimental Study of Boiling Critical Heat Flux with Low Mass Flux under Motion Condition in a Wetted Perimeter Equivalent Rod

Numerical Investigation on Boiling Crisis in a Full-Length 5 × 5 Fuel Assembly under Typical Pressurized Water Reactor Conditions

Critical heat flux measurement and visualization in R-134a on a vertical single rod with and without mixing-vanes spacer: The characteristics and phenomenon of critical heat flux

A Blowdown Critical Heat Flux Experimental Vehicle

Experimental Analysis of Fast-Transient Flow Boiling in Various Flow Conditions Using Inverse Heat Conduction Calculation Method

A CHF Correlation and Flow Pattern Observation on a Downward-Facing Boiling Surface

Prediction of Critical Heat Flux for Subcooled Flow Boiling in Annulus and Transient Surface Temperature Change at CHF

Critical Heat Flux and Heat Transfer Behaviors on Aged RPV Outer Wall Surface in Flow Boiling under IVR Conditions

OpenFOAM CFD simulation of critical heat flux in vertical pipe under typically PWR conditions

Investigation on the Critical Heat Flux in Typical 5 by 5 Rod Bundle at Conditions Prototypical of PWR Based on CFD Methodology

Experimental Investigation on Heat Transfer Characteristics in a Safety Injection Nozzle Component in PWR

The Characteristics and Correlation of Saturated Pool Boiling Critical Heat Flux for Downward-Facing Plain Heating Surface

Prediction Of subcooled water flow boiling critical heat flux (CHF) at low pressure

Experimental Investigation On Critical Heat Flux From Downward Facing Flat Plate For Different Orientation Angles

Experimental Investigation on Saturated Pool Boiling CHF for Downward Facing Heating Surface with Different Sizes and Aspect Ratio

Fluid-to-Fluid Modelling of CHF at High-Pressure Subcooled Water Conditions

Fluid-to-fluid Modeling of Critical Heat Flux in 4×4 Rod Bundles

A Theoretical CHF Model for Downward Facing Surfaces and Gaps under Saturated Boiling

Experimental Study on Critical Heat Flux During Flow Boiling of R134a in a Vertical Helically Coiled Tube

Effect of Heater Material and Thickness on the Steady-State Flow Boiling Critical Heat Flux