Abstract:The development of friction stir welding (FSW) created the basic foundation for friction stir processing (FSP). This process entails refining the local microstructure and achieving the localised plastic deformation due to the stirring effect of the tool, which may involve adding additional filler material as required. The rotating tool involved in the process has a shoulder and pin responsible for heat generation for plastic deformation and localised mixing. The rotating tool is inserted and traversed on the desired surface, tailoring the material properties. The tool's exposure to the surface causes localised plastic deformation and thermal gradient, and microstructural changes occur locally. The present investigation uses Friction Stir Processing (FSP) to fabricate an aluminium metal matrix composite. Recently, the use of aluminium alloy has been replaced by composites because of their increased mechanical and physical properties (specific properties). The experiment leads to manufacturing an aluminium metal matrix composite using aluminium oxide, boron carbide and commercially pure copper dust. Later, the effect of heat treatment on the respective metal matrix composite is studied. A comparative study among three different types of FSP techniques viz. FSP, Reinforced FSP, and Heat-treated Reinforced FSP have been performed. The tool revolution speed (RPM) and tool traverse speed of 400 RPM and 10 mm/min had been implemented, respectively. The T4 Heat-Treatment cycle was used during the current investigation. This investigative study was performed to analyse the changes in grain sizes and hardness values at the stir zone (SZ), thermo-mechanically affected zone (TMAZ), heat affected zone (HAZ) and on the base materials (BM) of the samples. The reinforced FSP metal matrix composite (MMC) showed an 81.26% increase in the micro-hardness value (HV) compared to the base metal. Further on analysing the microstructures, the reinforced FSP composite showed a 65.20% reduction in grain size. Moreover, the Heat-Treated sample showed an increase in the micro-hardness value by 99.8%.

Evaluation of Ca-alloyed and HAp-reinforced magnesium matrix surface composite properties developed by friction stir processing

Development of Al-Mg2Si Alloy Hybrid Surface Composites by Friction Stir Processing: Mechanical, Wear, and Microstructure Evaluation

Exploring the mechanical, metallurgical, and fracture characteristics of hybrid-reinforced magnesium metal matrix composite synthesized via friction stir processing route

Surface metal-matrix composites based on AZ91 magnesium alloy via friction stir processing: A review

Investigation on Mechanical and Fracture Behavior of Magnesium Composite Reinforced With Hybrid Fly Ash Particulates Synthesized via Friction Stir Processing Route

In-vitro bio-corrosion behavior of friction stir additively manufactured AZ31B magnesium alloy-hydroxyapatite composites

Enhancing microstructural and mechanical properties of magnesium AZ31 matrix composites through friction stir processing incorporating silicon carbide, titanium carbide, and graphite particles

Friction stir processing based surface modification of AZ31 magnesium alloy

Wear and Mechanical Behaviour of Magnesium AZ31 alloy Reinforced with MoS2 through Friction Stir Processing for Aerospace Applications

Comparative study of microstructural evolution and mechanical properties in friction stir processed, reinforced friction stir processed, and heat-treated reinforced friction stir processed Al composites

Mechanical properties and corrosion behavior of a friction stir processed magnesium alloy composite AZ31B–SiC

Study on surface modification and fabrication of surface composites of magnesium alloys by friction stir processing: a review

Metallurgical, mechanical and tribological behavior of Reinforced magnesium-based composite developed Via Friction stir processing

Synergistic effect of hybrid reinforcement on magnesium-based composites for enriching mechanical and tribological characteristics

Magnesium-based nanocomposites synthesized using friction stir processing: an experimental study

Fabrication of high-performance biomedical rare-earth magnesium alloy-based WE43/hydroxyapatite composites through multi-pass friction stir processing

Microstructural evaluation and corrosion properties of aluminium matrix surface composite adding Al-based amorphous fabricated by friction stir processing

Enrichment in Fracture Ductility Tribological Characteristics of Magnesium-Based Nanocomposites Fabricated via Multi-pass Friction Stir Processing and Study of Significant Parameters

Influence of Silica rich HNT/MoS2 Hybrid Reinforcements on Mechanical, Wear and Corrosion Characteristics of Magnesium AZ31 alloy

Fretting Fatigue Behavior of Magnesium Metal Matrix Composite Fabricated Through Friction Stir Processing Using Nickel Reinforced Particles

Investigation on microstructure, mechanical and tribological properties of friction stir processing of AZ31/AlFeCrMoNb surface composite