Abstract:The effects of different modeling and solving approaches on the simulation of a steam ejector have been investigated with the computational fluid dynamics (CFD) technique. The four most frequently used and recommended turbulence models (standard k-ε, RNG k-ε, realizable k-ε and SST k-ω), two near-wall treatments (standard wall function and enhanced wall treatment), two solvers (pressure- and density-based solvers) and two spatial discretization schemes ( the second-order upwind scheme and the quadratic upstream interpolation for convective kinematics (QUICK) of the convection term have been tested and compared for a supersonic steam ejector under the same conditions as experimental data. In total, more than 185 cases of 17 different modeling and solving approaches have been carried out in this work. The simulation results from the pressure-based solver (PBS) are slightly closer to the experimental data than those from the density-based solver (DBS) and are thus utilized in the subsequent simulations. When a high-density mesh with y+ < 1 is used, the SST k-ω model can obtain the best predictions of the maximum entrainment ratio (ER) and an adequate prediction of the critical back pressure (CBP), while the realizable k-ε model with the enhanced wall treatment can obtain the best prediction of the CBP and an adequate prediction of the ER. When the standard wall function is used with the three k-ε models, the realizable k-ε model can obtain the best predictions of the maximum ER, and the three k-ε models can gain the same CBP value. For a steam ejector with recirculation inside the diffuser, the realizable k-ε model or the enhanced wall treatment is recommended for adoption in the modeling approach. When the spatial discretization scheme of the convection term changes from a second-order upwind scheme to a QUICK scheme, the effect can be ignored for the maximum ER calculation, while only the CBP value from the standard k-ε model with the standard wall function is reduced by 2.13%. The calculation deviation of the ER between the two schemes increases with the back pressure at the unchoked flow region, especially when the standard k-ε model is adopted. The realizable k-ε model with the two wall treatments and the SST k-ω model is recommended, while the standard k-ε is more sensitive to the near-wall treatment and the spatial discretization scheme and is not recommended for an ejector simulation.

A Validation of CFD Methods on Predicting Valve Performance Parameters

Comparing research on two different numerical models of electrostatically actuated valveless micropump

Numerical simulation of 3-D turbulent flows in a cut-off valve and analysis of flow characteristics in pipe

Numerical Simulation of a Turbulence Flow in the Cut-off Valve by RNG k- ε Turbulence Model

Validation and Analyses of QCR Correction Turbulence Model in Sub-/Super-sonic Inner Flows

Effect of Relative Positions between Blade and Volute Tongue on Prediction of Performance in Simulation of Centrifugal Pump

The CFD Analysis of Cavitation Erosion and Structural Optimization for an Unloading Valve

Numerical Investigation of Cavitating Flow Behind the Cone of a Poppet Valve in Water Hydraulic System

Assessment of Different CFD Modeling and Solving Approaches for a Supersonic Steam Ejector Simulation

Effects of computational grids and turbulence models on numerical simulation of centrifugal pump with CFD

Effect of Suction and Discharge Conditions on the Unsteady Flow Phenomena of Axial-Flow Reactor Coolant Pump

Numerical Investigation of Cavitation Flow Inside Spool Valve with Large Pressure Drop

Appropriate CFD Models for Simulating Flow Around Spur Dike Group along Urban Riverways

Assessment Of Performance Of Turbulence Models Of Cfx In Predicting Supercritical Water Heat Transfer In A Vertical Tube

Formulations and Validations of a High-Precision Volume-of-Fluid Algorithm on Nonorthogonal Meshes for Numerical Simulations of Gas Entrainment Phenomena

Application of different turbulence models in numerical simulation of mixed-flow pump and its evaluation

Performance assessment of turbulence models in CFX for predicting heat transfer of supercritical water

Influence of turbulence model on performance prediction of mixed-flow pump

Errors and uncertainties in CFD validation for non-equilibrium turbulent boundary layer flows at high Reynolds numbers

Effect of wall stress models and subgrid-scale models for flow past a cylinder at Reynolds number 3900

Possible User-Dependent CFD Predictions of Transitional Flow in Building Ventilation