Abstract:The intermediate temperature deformation behavior and microstructural evolution of a spray formed 7075 Al alloy were performed at temperatures 60–120 °C with strain rates 0.00001–0.1 s −1 . The results reveal that the softening mechanism of the intermediate temperature deformation is dynamic recovery (DRV), which can be quantitated by Zener-Hollomon ( Z ) parameter. The constitutive equation can reasonably predict the stress-strain behavior of the alloy at intermediate temperatures. The activation energy is related to the deformation process and the interactions of the substructure, the average value is 140.1 kJ/mol. The higher efficiency of power dissipation in the processing map is related to the DRV at lower deformation temperatures. The optimum processing domain is located at the temperature of 90–120 °C and strain rate of 0.006–0.1 s −1 with a power dissipation efficiency range of 20%–40%. The processing parameters of the intermediate temperature deformation should be strictly controlled according to the strain. The uniform microstructure of 7075 alloys obtained by spray forming is crucial to overcome the disadvantage of poor deformability. The inferior coordinated deformation facilitates crack propagation at low strain rates. The high-density dislocation provides adequate nucleation sites for dynamic precipitation. The level of dynamic restoration facilitates the transformation from low angle grain boundaries (LAGBs) to high angle grain boundaries (HAGBs). The dislocations move to the grain/sub-grain boundary to form dislocation walls at low temperatures. The contribution to the stress from grain boundary (13.2–17.7 MPa), nanoscale precipitates (65.7–191.5 MPa), and dislocation (5.9–23.4 MPa) increases the difficulty of deformation. The deformation process at higher temperatures (105–120 °C) can be facilitated by the dissolution and coarsening of the nanoscale precipitates, and dislocation motion at the grain boundary.

Research on forming properties of 7075 aluminum alloy tubes by power staggered spinning

Spinning Process of 2219 Aluminum Alloy Tubes for Used in Hydroforming

Plasticity Improvement of Ball-Spun Magnesium Alloy Tube Based on Stress Triaxiality

Microstructure and Properties Evolution of 7075 Al alloy in Hot Rolling and Short Process Heat Treatment

Hot Gas Pressure Forming and Post Aging Treatment of Ti-22Al-24.5Nb-0.5Mo Square Tubes

Effect of Multi-Pass Power Spinning on Microstructure Homogenization and Mechanical-Property Strengthening of Ti2AlNb-Based Alloy Using Welded Tube Blank

Experimental and Numerical Investigation on Strengthening Behavior of 7075 Aluminum Alloy Sheets in Hot Forming–Quenching Integrated Process

Effects of Oxide Fragments on Microstructure and Mechanical Properties of AA6061 Aluminum Alloy Tube Fabricated by Thermomechanical Consolidation of Machining Chips

Comprehensive study of hot compression behaviors and microstructure evolution of solutionized 6082 aluminum alloy extruded bar

Study on interface behavior and mechanical properties of Al/Cu laminated tubes fabricated by strong staggered spinning at room temperature

Manufacturing of high strength thin-walled aluminum 6063 tubes through severe plastic deformation combined with peak-aging treatment

Microstructures and Mechanical Properties of 7075 Aluminum Alloy Semi-solid Billet by Hot Rolling

The Deformation Behavior and Microstructure Evolution of Cladding Tube during Spinning Composite Process of Mg/Al Tube

Effect of Rotational Shear and Heat Input on the Microstructure and Mechanical Properties of Large-Diameter 6061 Aluminium Alloy Additive Friction Stir Deposition

Microstructure evolution and tensile mechanical properties of thixoformed high performance Al-Zn-Mg-Cu alloy

Experimental Investigation of Current Intensity and Feed Speed in Electrically Assisted Necking and Thickening of 5A02 Aluminum Alloy Tubes

Modified constitutive model and workability of 7055 aluminium alloy in hot plastic compression

Research on power spinning process of 2A12 aluminum alloy thin-walled parts

Hot tensile deformation behavior and microstructure evolution of 7075 aluminum alloy sheet

Influence of Inner Roller Geometric Parameters on Counter-Roller Spinning with 6061 Aluminum Alloy Tube

Intermediate temperature tensile behavior and processing map of a spray formed 7075 aluminum alloy