Abstract:Heterogeneous metallic structures constitute a novel class of materials with excellent mechanical properties. However, the existing process for obtaining heterostructures from a single material does not meet large-scale industrial requirements. In this study, a pure copper heterostructured laminate (HSL) composed of a surface elongated-grain layer and a central equiaxed-grain layer was fabricated by rolling bonding and annealing. To study the effect of the interface on the mechanical properties of gradient-structured materials, both laminate metal composite (LMC) and non-composite laminate (NCL) were fabricated by cold-rolling pretreatment of the center layer (60% reduction) and cold-rolling bonding of the whole blank (67% reduction). Then, the HSL was obtained by controlling the post-annealing regimes, the microstructure of each layer was optimized, and a larger degree of microstructural heterogeneities, such as grain size, misorientation angle, and grain orientation, was obtained, which resulted in obvious mechanical differences. Tensile tests of the HSL, surface layer, center layer, and NCL specimens revealed that the HSL annealed at 300 °C for 1 h had a significantly higher strength than the center layer and a higher elongation than the surface layer. The HSL had a tensile strength and elongation at fracture of 278.08 MPa and 46.2%, respectively, indicating a good balance of strength and plasticity. The improved properties were primarily attributed to the strengthening or strain hardening due to the inhomogeneous deformation of the heterogeneous layers in the laminate and the mutual constraint acquired by the distinct layers with strong mechanical differences. The HSL had an interfacial bonding strength of 178.5 MPa, which played a vital role in the coordinated deformation of the heterogeneous layers. This study proposes an HSL design method that effectively simplifies the process of obtaining heterostructures in homogeneous materials by controlling the cumulative deformation of the surface and center layers.

A Novel Technique for Controllable Fabrication of Multilayer Copper/Brass Block

Multilayer Graphene Interface Enabled Ultrahigh Extensibility for High Performance Bulk Nanostructured Copper

High Reflectivity and Thermal Conductivity Ag–Cu Multi-Material Structures Fabricated via Laser Powder Bed Fusion: Formation Mechanisms, Interfacial Characteristics, and Molten Pool Behavior

A Facile and Sustainable Integrated Fabrication Strategy for Multi-Performance 316l Stainless Steel

Mechanical properties and fracture behavior in copper-brass heterostructured fibers

Fabrication of robust hierarchical micro/nanostructures on tin-bronze substrate

Three-dimensional micro-fabrication on copper and nickel

Interface Microstructure and Mechanical Properties of Copper-Steel Joints with Nickel Transition Layer Prepared by Ultrasonic Additive Manufacturing

Achieving Novel Copper–steel Joints with a Combination of High Strength and Ductility Reinforced by In-Situ Fe-rich Particles

Friction stir additive manufacturing enabling scale-up of ultrafine-grained pure copper with superior mechanical properties

Additive manufacturing of micro-architected copper based on an ion-exchangeable hydrogel

Achieving high strength and high ductility in WC-reinforced iron-based composites by laser additive manufacturing

A dual heterogeneous laminated microstructure design for improving the mechanical properties and electrical conductivity of copper alloys

Mechanical Properties Optimization and Microstructure Analysis of Pure Copper Heterostructured Laminates via Rolling

Enhancing the interface strength of additively manufactured 316 L/CuSn10 bimetallic components through heterogeneous microstructures

Sustainable Fabrication of Cu/Nb Composites with Continuous Laminated Structure to Achieve Ultrahigh Strength and Excellent Electrical Conductivity

Additive manufacturing of micro‐architected copper based on an ion‐exchangeable hydrogel

Interface microstructure and mechanical properties of copper/304 stainless steel dissimilar joint assisted by Ni transition layer using ultrasonic additive manufacturing (UAM)

Fabrication of 3D Metal Microstructures Using a Hybrid Process of Micro-EDM and Laser Assembly

Anisotropic material properties of pure copper with fine-grained microstructure fabricated by laser powder bed fusion process

Selective laser melting 316L/CuSn10 multi-materials: Processing optimization, interfacial characterization and mechanical property