Abstract:The durability of infrastructure materials, such as concrete, has direct impact on society because the productivity of many industries and safety of human beings depend on infrastructure condition, and further because maintenance of the infrastructure can represent a significant portion of a government’s budget. Thus the enhancement of concrete durability and improvement of infrastructure condition monitoring are significant concerns to the scientific community. The resonant frequency method has been traditionally used to assess the mechanical condition of concrete. Resonance frequencies of a solid body depend on test sample mass and dimensions, elastic properties, and boundary conditions. Resonance frequencies have been used to determine engineering properties such as the elastic moduli and material damping. The method is useful to assess the performance of materials within accelerated degradation durability test procedures, and to inspect quality of the products during manufacturing processes (pass/fail tests). Different testing standards and recommendations prescribe test configurations, and specific tests are recommended for different materials. A basic resonant frequency test requires a forced vibration system to set up mechanical resonances, and some system to sense the frequency content from the resonant vibration signals. For concrete-like materials, these specifications are given by ASTM C215 [1], wherein an impulsive impact event is applied to the test sample to excite the resonant frequencies and a small sensor is mounted on the surface of the test sample. From the impulsive impact vibration signals thus obtained, two standard parameters are usually derived: (1) the dynamic modulus, which depends on sample dimensions, mass, and the resonant frequency peak (f), and (2) the attenuation or damping capacity of the material. Figure 12.1a, b illustrates typical signals obtained from a single-impact vibration test, where the spectral (frequency domain) signal is computed from the time signal using a Fourier transform algorithm. The continuous reduction of the vibration signal amplitude with time during the signal “ring-down” is seen in the time domain signal. The resonant frequency and damping characteristics are extracted from the spectral signal in the region around the resonant frequency peak. The damping capacity of the material is determined from the quality factor (Q) (or inverse attenuation), which is defined as the ratio between the resonant frequency peak (f) and the bandwidth frequencies corresponding to a 50% reduction of vibration energy in the power frequency spectrum for a given vibration mode [2]. Meaningful application of the ASTM C215 test is found within other standard durability test methods [3, 4].

Nonlinear Impact-Echo Test for Quantitative Evaluation of ASR Damage in Concrete

Assessment of alkali–silica reaction damage through quantification of concrete nonlinearity

DETECTION OF CONCRETE DAMAGE USING NONLINEAR IMPACT RESONANCE ACOUSTIC SPECTROSCOPY

Rapid Evaluation of Compressional Damage in Concrete Using Air-coupled Nonlinear Resonance Frequency Shift Technique

Accelerated Determination of ASR Susceptibility During Concrete Prism Testing Through Nonlinear Resonance Acoustic Spectroscopy

Concrete damage diagnosed using the non-classical nonlinear acoustic method

Single-Impact Nonlinear Resonant Acoustic Spectroscopy for Monitoring the Progressive Alkali–Silica Reaction in Concrete

Rapid Evaluation of Alkali–silica Reactivity of Aggregates Using a Nonlinear Resonance Spectroscopy Technique

Enhancement of Contact Acoustic Nonlinearity Effect in a Concrete Beam using Ambient Vibrations

Cement-Based Material Characterization Using Nonlinear Single-Impact Resonant Acoustic Spectroscopy (NSIRAS)

Wave mixing technique for nondestructive assessment of alkali-silica reaction damage in concrete prism samples

Experimental study of concrete damage evaluation based on acoustic emission technique

QUANTITATIVE CONCRETE-DAMAGE EVALUATION BY ACOUSTIC EMISSION INFORMATION AND RATE-PROCESS THEORY

Lattice Discrete Particle Modeling of acoustic nonlinearity change in accelerated alkali silica reaction (ASR) tests

Damage Detection of Concrete Structures Using Acoustic Emission

Experimental study on the nonlinear mixing of ultrasonic waves in concrete using an array technique

Use of the Impact-Echo Method to Evaluate Damage due to Distributed Cracking in Concrete Plate Members: Theory and Field Trials

A chemo-mechanical model for the acoustic nonlinearity change in concrete with alkali-silica reactions

Vibro-acoustic modulation and data fusion for localizing alkali–silica reaction–induced damage in concrete

Evaluation of deterioration in reinforced concrete structures by AE technique

Evaluation of alkali–silica reaction damage in concrete by using acoustic emission signal features and damage rating index: damage monitoring on concrete prisms