Abstract:The durability of infrastructure materials, such as concrete, has direct impact on society because the productivity of many industries and safety of human beings depend on infrastructure condition, and further because maintenance of the infrastructure can represent a significant portion of a government’s budget. Thus the enhancement of concrete durability and improvement of infrastructure condition monitoring are significant concerns to the scientific community. The resonant frequency method has been traditionally used to assess the mechanical condition of concrete. Resonance frequencies of a solid body depend on test sample mass and dimensions, elastic properties, and boundary conditions. Resonance frequencies have been used to determine engineering properties such as the elastic moduli and material damping. The method is useful to assess the performance of materials within accelerated degradation durability test procedures, and to inspect quality of the products during manufacturing processes (pass/fail tests). Different testing standards and recommendations prescribe test configurations, and specific tests are recommended for different materials. A basic resonant frequency test requires a forced vibration system to set up mechanical resonances, and some system to sense the frequency content from the resonant vibration signals. For concrete-like materials, these specifications are given by ASTM C215 [1], wherein an impulsive impact event is applied to the test sample to excite the resonant frequencies and a small sensor is mounted on the surface of the test sample. From the impulsive impact vibration signals thus obtained, two standard parameters are usually derived: (1) the dynamic modulus, which depends on sample dimensions, mass, and the resonant frequency peak (f), and (2) the attenuation or damping capacity of the material. Figure 12.1a, b illustrates typical signals obtained from a single-impact vibration test, where the spectral (frequency domain) signal is computed from the time signal using a Fourier transform algorithm. The continuous reduction of the vibration signal amplitude with time during the signal “ring-down” is seen in the time domain signal. The resonant frequency and damping characteristics are extracted from the spectral signal in the region around the resonant frequency peak. The damping capacity of the material is determined from the quality factor (Q) (or inverse attenuation), which is defined as the ratio between the resonant frequency peak (f) and the bandwidth frequencies corresponding to a 50% reduction of vibration energy in the power frequency spectrum for a given vibration mode [2]. Meaningful application of the ASTM C215 test is found within other standard durability test methods [3, 4].

DETECTION OF CONCRETE DAMAGE USING NONLINEAR IMPACT RESONANCE ACOUSTIC SPECTROSCOPY

Rapid Evaluation of Compressional Damage in Concrete Using Air-coupled Nonlinear Resonance Frequency Shift Technique

Concrete damage diagnosed using the non-classical nonlinear acoustic method

Nonlinear Impact-Echo Test for Quantitative Evaluation of ASR Damage in Concrete

Detection and Quantification of Damage in Metallic Structures by Laser-Generated Ultrasonics

Concrete damage nonlinear detection based on embedded ultrasonic sensors

Assessment of alkali–silica reaction damage through quantification of concrete nonlinearity

Concrete Microcracks Detection under Compressive Load Based on Nonlinear Ultrasonics Modulation with Broadband Excitation

Cement-Based Material Characterization Using Nonlinear Single-Impact Resonant Acoustic Spectroscopy (NSIRAS)

Non-contact Assessment of Thermal Damage of Concrete Using a Nonlinear Wave Modulation Technique

Structure Damage Detection Method Based on Adaptive Stochastic Resonance Technology and Response Sensitivity Method

Nondestructive Assessment of Microcracks Detection in Cementitious Materials Based on Nonlinear Ultrasonic Modulation Technique

RAPID ASSESSMENT OF ALKALI‐SILICA REACTION DAMAGE IN CEMENT MORTARS BY NONLINEAR ACOUSTIC TECHNIQUE

Research Strategy and Application of Vibration-Based Non Destructive Structural Damage Detection

DETECTION OF DAMAGE IN CONCRETE STRUCTURE VIA SHIFTS IN NATURAL FREQUENCY

Single-Impact Nonlinear Resonant Acoustic Spectroscopy for Monitoring the Progressive Alkali–Silica Reaction in Concrete

Enhanced concrete crack detection using nonlinear ultrasonic signal denoising and feature enhancement with CEEMDAN, VMD and GRU

Nonlinear Ultrasonic Second Harmonic Assessment of Concrete Defects Based on Embedded Piezoelectric Sensors

MICROCRACKS DETECTION OF THERMAL DAMAGED CONCRETE WITH NONLINEAR ULTRASONIC MODULATION BASED ON BROAD BAND FREQUENCY COUPLING

Rapid Evaluation of Alkali–silica Reactivity of Aggregates Using a Nonlinear Resonance Spectroscopy Technique

To Evaluate the Degradation of Heat Damaged Concrete Specimens after Curing Using Non-Linear Ultrasound Technique