Abstract:In this study, the role of feedstock powder in influencing the characteristics of cold spray deposition is explored. Four distinct types of Cu feedstock powders, derived through electrolysis and employing varied gas atomization methods, are applied to a Cu substrate via low-pressure cold spray coating. We investigated the impact of feedstock powder on the resultant coatings' microstructure and mechanical properties. A comprehensive statistical model is developed, considering the cold spray parameters, weight change, coating thickness, and discerning their significance and interactions. Optimal conditions for carrier gas temperature and pressure are identified at approximately 400 °C and 1.99 MPa, respectively, consistent across all Cu powders. Velocity analysis reveals particle velocities ranging from 373 to 564 m/s under these optimal conditions. Coatings deposited using satellite-free gas-atomized powder, characterized by enhanced sphericity, exhibit superior characteristics, including minimal porosity (0.66 ± 0.35%), high flattening ratio (3.57 ± 1.51), elevated microhardness (107 ± 3 HV) and high bonding strength (20.7 ± 2.3 MPa). In contrast, coatings deposited with gas-atomized powder featuring microsatellite particles and electrolytic powder with irregular shapes display distinct properties. The observed trends are attributed to lower oxygen content and reduced oxide levels near the surface of the more spherical, satellite-free powder. This powder also demonstrates heightened plastic deformation during deposition. The increased peening effect of satellite-free gas-atomized powder during cold spray results in elevated dynamic recrystallization near the substrate surface, leading to smaller grains at the interface. Microstructural evolution analysis, utilizing electron backscatter diffraction, further elucidates the heterogeneous deformation and grain refinement occurring in Cu splats during cold spray coating.

Microstructural and Micromechanical Analysis of Cold Sprayed CrMnCoFeNi High Entropy Cantor Alloy Coatings

Microstructural, Micromechanical, Wear, and Corrosion Properties of Cold Spray and Laser-Assisted Cold Spray CrMnCoFeNi Cantor HEA Coatings

Cold Spray and Laser-Assisted Cold Spray of CrMnCoFeNi High Entropy Alloy Using Nitrogen as the Propelling Gas

Structure Evolution and Corrosion Performance of CoCrFeMnNi High Entropy Alloy Coatings Produced Via Plasma Spray and Cold Spray

Optimizing Cold Spray Parameters for High Entropy Alloy Coatings Using Taguchi and Box–Behnken Design Approaches for Mechanically Alloyed Powder

Cold Gas Spraying of a High-Entropy CrFeNiMn Equiatomic Alloy

Investigation of the Structure and Properties of a Coating from a High-Entropy FeCoCrNiMn Alloy Obtained by a Wire Arc Additive Manufacturing

Microstructure and mechanical performance of cold spray Cr coatings

Comparative Analysis of Microstructural and Mechanical Attributes in Low-Pressure Cold-Spray Coatings: Impact of Varied Cu Feedstock Powders

Fabrication of cBN-NiCrAl Cermet Coating by Cold Spray

Microstructure characterization of AlCoCrFeNiTi high-entropy alloy coating produced by atmospheric plasma spraying

Multiple strengthening mechanisms of cold-sprayed cBNp/NiCrAl composite coating

Microstructure and Properties of Cu–Cr Coatings Deposited by Cold Spraying

In-situ Observation of Microstructure Evolution of Cold Sprayed CrZrCu Alloy Coating During Heating

MICROSTRUCTURE CHARACTERISTICS OF Cr3C2-NiCr COATINGS DEPOSITED WITH THE HIGH-VELOCITY OXY-FUEL THERMAL-SPRAY TECHNIQUE

Microstructure and wear behavior of FeCoNiCrMn high entropy alloy coating deposited by plasma spraying

Structural analysis and mechanical properties of some coatings obtained by cold spray method. A review

Formation of Fe-Al Intermetallic Compound Coating Through Cold Spraying

The Influence of Spraying Parameters and Powder Sizes on the Microstructure and Mechanical Behavior of Cold-Sprayed Inconel®625 Deposits

Influence of Annealing on the Microstructure and Wear Performance of Diamond/NiCrAl Composite Coating Deposited Through Cold Spraying

Microstructure and tribological properties of Al2O3 reinforced FeCoNiCrMn high entropy alloy composite coatings by cold spray