Abstract:Transition metal based high entropy alloys (HEAs) are often used in electrocatalytic (water electrolysis) applications due to the synergistic effect operating among its constituent elements and unpaired electrons in d orbitals of the concerned metal. In this study, a low cost NiMnFeCu high entropy alloy was successfully synthesised using the combined techniques of mechanical milling (MA) and vacuum sintering. X-ray diffraction was used to analyse the phase composition, optical microscopy, and scanning electron microscopy were used to characterise the fabricated material’s microstructure and chemical homogeneity, thermal, and mechanical properties were tested using the differential scanning calorimetry method and a universal testing machine, respectively. Electrochemical workstation was used to carry out preliminary electrochemical studies such as linear sweep voltammetry (LSV), cyclic voltammetry (CV) and chronoamperometry. The results showed that the as- sintered NiMnFeCu HEA possessed a single- phase FCC structure. The HEA NiMnFeCu sintered at 1050 °C (S4) and 1000 °C (S2) with a holding time of 2 h showed a yield strength of 516.3 MPa and 389.8 MPa, respectively, and the micro-hardness values were measured to be 233.45 ± 9 HV and 198.7 ± 8 HV, respectively. Preliminary electrochemical studies proved that the alloy sintered at 1000 °C (S2) with a holding time of 2 h exhibited excellent electrocatalytic properties with a measured overpotential of 322 mV at 10 mA cm−2 at 100 cycles of CV and good stability for 10 h when compared to state-of-the-art electrocatalytic materials IrO2 and RuO2. This suggested that the HEA NiMnFeCu fabricated under the condition S2 could potentially be used for industrial-scale water electrolysis as it possesses permissible mechanical and good electrochemical properties.

Direct electrodeposition of CoFeNiMoW high entropy alloy thin films from aqueous medium

Electrolytic Deposition of Hydroxyapatite Coating on CoNiCrMo Substrates

Facile Preparation of Fe-Co-Ni-Mo-W High Entropy Alloy Coatings from An Aqueous Bath by Direct Current Electrodeposition: Microstructure and Performance

Electrodeposition, Characterization, and Corrosion Behavior of CoCrFeMnNi High-Entropy Alloy Thin Films

Electrodeposited NiFeCoMoW High-Entropy Alloys with Nanoscale Amorphous Structure As Effective Hydrogen Evolution Electrocatalysts

Mechanical properties of nanostructured CoCrFeNiMn high-entropy alloy (HEA) coating

Electrodeposition of high entropy alloy coating from water bath

Microstructures and properties of FeCoNiCr high-entropy alloy coatings prepared by electrodeposition

Fabrication of Single-Crystalline CoCrFeNi Thin Films by DC Magnetron Sputtering: A Route to Surface Studies of High-Entropy Alloys

Synthesis of CoCrFeMnNi High Entropy Alloy Thin Films by Pulse Electrodeposition: Part 1: Effect of Pulse Electrodeposition Parameters

Mesoporous High-Entropy Alloy Films

Electrodeposition of High Entropy Alloy of Ni-Co-Cu-Mo-W from an Aqueous Bath

CoCrFeMnNi High-Entropy Alloy Thin Films Electrodeposited on Aluminum Support

Synthesis and structural characterizations of CrCoFeNiMnx (0 ≤ x ≤ 1) high-entropy-alloy thin films by thermal reduction in hydrogen

CoNiWReP high entropy alloy coatings prepared by pulse current electrodeposition from aqueous solution

Fabrication, Microstructure, Mechanical, and Electrochemical Properties of NiMnFeCu High Entropy Alloy from Elemental Powders

Microstructure and properties of FeCoNiCrX (X=Mn, Al) high-entropy alloy coatings

Preparation of CoCrFeNi High-Entropy Alloy via Electro-Deoxidation of Metal Oxides

Effect of Additive and Current Density on Microstructures and Corrosion Behavior of a Multi-Component NiFeCoCu Alloy Prepared by Electrodeposition

Preparation of FeCoNiCrMn High Entropy Alloy by Electrochemical Reduction of Solid Oxides in Molten Salt and Its Corrosion Behavior in Aqueous Solution

Microstructure and electrochemical properties of FeCoNiCuZn high-entropy alloy films by DC electrodeposition