Abstract:The techniques for releasing thermal energy accumulated in periods of high availability to meet the demand in periods of low energy supply contribute to the continuity of the cycles involved in thermodynamic processes. In this context, phase change materials are capable of absorbing and releasing large amounts of energy in relatively short periods of time and under specific operating conditions. However, phase change materials have low thermal conductivity and need to be coupled with high-thermal-conductivity materials so that the heat flux can be intensified and the energy absorption and release times can be controlled. This work aims to numerically study the solidification process of a phase change material inserted into a triplex tube heat exchanger with finned copper walls to intensify the thermal exchange between the phase change material and the cooling heat transfer fluid, water, that will receive the energy accumulated in the material. This work proposes the 3D numerical modeling of the triplex tube heat exchanger with finned walls and meets the need for numerical models that allow for the analysis of the full geometry of the latent heat thermal energy storage system and the thermal and fluid dynamic phenomena that are influenced by this geometry. Results of the temperature, liquid fractions and velocity fields during phase transformations are presented, analyzed and validated with experimental data, presenting average errors of below 5%. The total material discharge time was approximately 168 min, necessary for the complete solidification of the phase change material, with water injected into the triplex tube heat exchanger at a flow rate of 8.3 L/min and a temperature of 68 °C. The solidification process occurred more slowly in the same direction as the length of the triplex tube heat exchanger, and from 80% of the material in the solid state, the difference between the solidification time for z = 0 and z = 480 mm was 30 min. The fluid dynamic conditions developed in the latent heat thermal energy storage system promoted a maximum negative heat flux of −6423 w/m2 to the annular internal surface and −742 w/m2 to the annular external surface, representing a heat removal process nine times less intense on the external surface. The total energy released to the cooling heat transfer fluid was 239.56 kJ/kg.

NUMERICAL SOLUTION OF COUPLED HEAT TRANSFER WITH PHASE-CHANGE AND THERMITE REACTION

Thermal behavior of aluminothermic thermite reaction for application in thermal sealing of oil wells

Experimental investigation of AL-Fe2O3 thermite reactions for thermal plug and abandonment of oil wells

Full factorial design analysis of thermodynamic and kinetic parameters in simulated thermite reaction propagation

Semi-Analytical Solution of a Nonlinear Heat Transfer Model for a Tubular Cocurrent Moving-Bed Reactor With a First-Order Chemical Reaction in the Solid Phase

NUMERICAL SIMULATION OF ENHANCED CONVECTION HEAT TRANSFER USING METHANE-STEAM REFORMING IN CATALYST FILMS IN A VERTICAL TUBE

3D Numerical Analysis of a Phase Change Material Solidification Process Applied to a Latent Thermal Energy Storage System

A Reduced Numerical Model for the Thermit Rail Welding Process

Numerical Simulation of Enhanced Heat Transfer in Tubes Using Methane Steam Reforming

Numerical Study of Heat Conduction with a Chemical Reaction at the Moving Frontal Surface for a Graphite Plate

Numerical Investigations of Heat Transfer in Phase Change Materials Using Non-Equilibrium Model

Thermal response and pyrolysis behavior of carbon fiber/phthalonitrile composites under one-sided butane flame heating: Experimental and numerical analysis

Mass and Heat Transfer of Thermochemical Fluids in a Fractured Porous Medium

Numerical modeling of diffusion-controlled phase transformations in ternary systems and application to the ferrite/austenite transformation in the Fe-Cr-Ni system

Theory for multicomponent diffusional kinetics and its application to the reaustenitisation of dual phase and TRIP steels

Thermo-mechanical response FEM simulation of ceramic refractories undergoing severe temperature variations

Numerical Simulation of Reacting Flow in the Combustion Chamber and Study of the Impact of Turbulent Diffusion Coefficients

A Numerical Method for Analysing Heat Conduction in Composites Containing Encapsulated Phase Change Materials

Two-phase numerical simulation of thermal and solutal transport exploration of a non-Newtonian nanomaterial flow past a stretching surface with chemical reaction

Numerical Study of the Counterflow Diffusion Flames of Methanol Hydrothermal Combustion: the Real-Fluid Effects and Flamelet Analysis

A 2D mechanical–thermal coupled model to simulate material mixing observed in friction stir welding process