Abstract:Fe-Si-B-P-Cu nanocrystalline alloy were treated with ball-mill using a lubricant as a process control agent (PCA). The resulting alloy powder is a strong candidate material for soft magnetic composites. Two ball milling methods (continuous and interval) were employed to control the interactions between the PCA and the alloy surface, and their effect on the microstructure of the prepared alloy particles was investigated. The alloy sheet was broken into small pieces and deformed plastically into flake-shaped particles regardless of the ball milling method implemented. Friction-force microscopy of the alloy immersed in the PCA revealed that the friction coefficient of the alloy surface exposed to air for a certain period was higher than that of the unexposed alloy surface (immediately after polishing). During ball milling, the ratio of the newly generated surface to the oxidized surfaces of the alloy subjected to interval milling was smaller than that of the alloy subjected to continuous milling. Therefore, the friction coefficient of the surface of the alloy subjected to interval milling was higher than that of the alloy subjected to continuous milling. Synchrotron radiation analysis revealed that the alloy subjected to interval milling exhibited enhanced surface friction, showing an obvious steepness and inflection in the diffraction intensity as a function of the tilt angle based on the Schulz reflection method. This indicates formation of crystallographic texture in α-Fe grains in an amorphous matrix. Hence, we demonstrated successfully that the ball milling process induced a crystallographic texture in the Fe-based nanocrystalline alloy due to plastic deformation due to the enhanced surface friction. The surface of the alloy was prepared based on the effect of the interfacial interactions between the alloy surface and the PCA.

Effect of mechanical milling on powder characteristics of Fe-based metal matrix composites reinforced with WC–Co and NbC particles

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

Comparative study of the microstructure and phase evolution of FeCoCrNiAl high-entropy alloy-matrix WC nanocomposite powders prepared by mechanical alloying

Influence of Milling Time on the Microstructure and Soft-Magnetic Properties of Nanocrystalline Fe72Ni8Co8Zr7B4Cu1

Mechanical properties of the Al-Mg/MWCNTs composite powders: The effects of ball milling process parameters

Effect of Milling Time and Process Control Agent on Microstructure and Mechanical Properties of AA2024-2 wt.% Cu Metal–Metal Composites Produced by Mechanical Alloying

Effects of milling time and sintering temperature on the mechanical properties of 8 wt% WC/AlCoCrFeNiTi 0.5 high entropy alloy matrix composite

Effect of particle size and high-energy ball milling time on microstructure and mechanical properties of WC-10Co cemented carbides with plate-like WC grains

Effect of milling time on microstructure and hardness of AA7075-15 wt% SiC-1 wt% MWCNT nanocomposite

Effect of ball milling time on the structural characteristics and mechanical properties of nano-sized Y2O3 particle reinforced aluminum matrix composites produced by powder metallurgy route

Effect of Milling Time and Reinforcement Volume Fraction on Microstructure and Mechanical Properties of SiCp-Reinforced AA2017 Composite Powder Produced by High-Energy Ball Milling

Structural and thermal properties of the Fe-based alloys prepared by mechanical milling

Effects of milling process parameters and PCAs on the synthesis of Al0.8Co0.5Cr1.5CuFeNi high entropy alloy powder by mechanical alloying

Effect of Milling Parameters on the Development of a Nanostructured FCC–TiNb15Mn Alloy via High-Energy Ball Milling

Effects of interfacial interactions between metal and process control agents during ball milling on the microstructure of the milled Fe-based nanocrystalline alloy powder

Fabrication of ultrafine and nanocrystalline WC–Co mixtures by planetary milling and subsequent consolidations

On effect of particle size distribution on the elastic/plastic deformation of metal matrix composites

Effect of Increasing the Strength of Aluminum Matrix Nanocomposites Reinforced with Microadditions of Multiwalled Carbon Nanotubes Coated with TiC Nanoparticles

Structural, magnetic and electron transfer effect of Cr additive on Fe 65 Co 35 nanopowder fabricated mechanical alloying

The effect of planetary milling conditions on tungsten-carbide (WC) particle size reduction and sintered properties