Abstract:In response to the safety concerns on highly flammable liquid electrolytes in lithium-ion batteries (LIBs), the all-solid-state batteries (ASSBs) have emerged as promising alternatives for the next generation. The use of solid electrolytes with low flammability can provide resistance to fire/explosion incidents under abnormal conditions. In addition, it is expected that high power and high energy density can be achieved using high-voltage cathode materials due to the wide electrochemical window of solid electrolytes. Therefore, various solid electrolytes (polymer, inorganic, and composite solid electrolytes) were intensively studied. Among the solid electrolytes, sulfide-based inorganic solid electrolytes have attracted much attention due to their advantages. They have the highest ionic conductivity (10 -2 ~ 10 -3 S cm -1 ) at room temperature, comparable to a liquid electrolyte. Also, owing to its ductile characteristics, interfacial contact with electrode material is also good, and large-scale production is advantageous. However, there are many problems to be solved to realize ASSB with sulfide-based electrolytes. one of the main obstacles is to produce sheet-type electrodes with high active mass loading and good stability. The slurry process commonly used to manufacture sheet-type electrodes of LIBs cannot be directly applied to ASSBs because sulfide-based electrolytes exhibit high reactivity with most organic solvents. Even if the reactivity is not considered, in the slurry process, the bulk binder surrounds the electrode components and blocks the ion transfer pathway, thereby degrading the cell performance. In this regard, solvent-free processing has emerged as a novel manufacturing process to overcome these issues. It is well known that polytetrafluoroethylene (PTFE) can fibrillate under shear stress conditions. When PTFE is added to the electrode and stress is applied, the PTFE is thinly fibrillated within the electrode. These well-dispersed fibers bind electrode materials and form sheet-type electrode film without delamination. This novel process has little concern about reactivity as no solvent is added, and PTFE does not react with electrode components. Moreover, since the thinly fibrous binder is evenly spread throughout the electrode, a sheet-type electrode can be formed with a smaller amount than in the slurry process, and the ion transfer pathway in the electrode can be less blocked. However, solvent-free processing also has problems to be solved. The thinly fibrillated binder cannot provide sufficient adhesion strength between the electrode components. The insufficient adhesion strength of the binder cannot prevent the reduction in the contact area between the electrode and the electrolyte material due to volume expansion during the charge/discharge process, resulting in rapid performance degradation. In this work, we pre-treated PTFE to increase adhesion strength between electrode components and the cycling stability of the solvent-free electrode. When comparing the mechanical strength of solvent-free electrodes using the Surface and Interfacial Cut Analysis System (SAICAS) tool, electrodes with pre-treated PTFE had higher mechanical strength than electrodes with bare PTFE. Due to the higher mechanical strength, the pre-treated PTFE electrode had better cycling stability than the electrode with bare PTFE. This pre-treatment technology is expected to be a promising technology that can contribute to the realization of large-scale production and commercialization of ASSBs.

Usage of Co-Solvent for Fabricating the Composite Cathode for Sulfide-Based All-Solid-State Lithium Batteries

Exploring the Concordant Solid-State Electrolytes for All-Solid-state Lithium-Sulfur Batteries

Polymer Binder with Improved Interfacial Property in the Composite Cathode for All-Solid-State Lithium Batteries

Highly conductive composite cathode prepared by dry process using Nafion-Li ionomer for sulfide-based all-solid-state lithium batteries

Exploring the Optimal Binder Content in Composite Electrodes for Sulfide-Based All-Solid-State Lithium-Ion Batteries

Sulfide-based Solid Electrolyte and Electrode Membranes for All-Solid-state Lithium Batteries

Slurry‐Fabricable Li+‐Conductive Polymeric Binders for Practical All‐Solid‐State Lithium‐Ion Batteries Enabled by Solvate Ionic Liquids

A Strategy to Suppress the Electrochemo-Mechanical Degradation in Solvent-Free Electrodes for All-Solid-State Batteries

Sulfide Based Solid Electrolyte for Lithium-Sulfur Batteries

Toward the Practical and Scalable Fabrication of Sulfide‐Based All‐Solid‐State Batteries: Exploration of Slurry Process and Performance Enhancement Via the Addition of LiClO4

Fusion Bonding Technique for Solvent‐free Fabrication of All‐solid‐state Battery with Ultra‐thin Sulfide Electrolyte

Wet-slurry fabrication using PVdF-HFP binder with sulfide electrolytes via synergetic cosolvent approach for all-solid-state batteries

In Situ Deprotection of Polymeric Binders for Solution-Processible Sulfide-Based All-Solid-State Batteries

Phase-Transition-Promoted Interfacial Anchoring of Sulfide Solid Electrolyte Membranes for High-Performance All-Solid-State Lithium Battery

LiI-Doped Sulfide Solid Electrolyte: Enabling a High-Capacity Slurry-Cast Electrode by Low-Temperature Post-Sintering for Practical All-Solid-State Lithium Batteries

Wet‐Processable Binder in Composite Cathode for High Energy Density All‐Solid‐State Lithium Batteries (Adv. Energy Mater. 35/2024)

Effect of Solvents on a Li10GeP2S12-Based Composite Electrolyte Via Solution Method for Solid-State Battery Applications.

Long‐Life Sulfide All‐Solid‐State Battery Enabled by Substrate‐Modulated Dry‐Process Binder

Styrene–Butadiene–Styrene Block Copolymer-Li5.5PS4.5Cl1.5 Composite Solid-State Electrolyte Enabling a High-Performance All-Solid-State Lithium Battery

Water-Soluble Trifunctional Binder for Sulfur Cathodes for Lithium–Sulfur Battery

Flexible Electrolyte and Cathode Membranes for All-Solid-State Batteries Fabricated by a One-Step Solvent Method