Abstract:This study utilizes a lab-developed pneumatic-extrusion condensing 3D food printer to prepare astragalus–starch mixed gels by blending different ratios of astragalus polysaccharide and wheat starch and applies these gels to 3D printing experiments. The aim of this paper is to investigate the impacts of mixed-gel concentrations on printing outcomes in order to identify the optimal blending ratio. Under this rationale, the effects of printing layer height and nozzle diameter on print quality were studied. Single-factor analysis and response surface methodology were employed to optimize the experiments and determine the optimal printing process parameters for the astragalus–starch mixed gels. The results indicate that an increase in astragalus polysaccharide content leads to a decrease in the sedimentation rate of the mixed gels and a tendency towards a more fluid consistency. After storage of samples in a sealed space for equal durations, it was found that an increase in astragalus polysaccharide content enhances the textural properties of the mixed gels, with optimal printing effects achieved at a 2% polysaccharide content. The optimal print quality is achieved when the ratio of nozzle diameter to layer height is between 0.5 and 0.55. The influence order of printing process parameters on the overall completion rate of the samples is nozzle diameter > printing speed > fill rate. The predicted optimal printing parameters are a nozzle diameter of 0.6 mm, a printing speed of 767 mm/min, and a fill rate of 83%, with a predicted overall completion rate of the printed samples at 99.45%. Experimental validation revealed an actual overall completion rate of the printed samples at 99.52%, slightly higher than the predicted value. This discrepancy was attributed to the precision of the measurement methods and the variability in the printing process. The study demonstrates that the addition of astragalus polysaccharide significantly improves the 3D printing molding effect of wheat starch, and the printing parameter settings obtained by response surface optimization effectively enhance printing accuracy. This research provides experimental evidence and parameter optimization references for the application of non-starch polysaccharides in starch-based 3D food printing.

Undaria pinnatifida gel inks for food 3D printing are developed based on the colloidal properties of Undaria pinnatifida slurry and protein/colloidal/starch substances

Investigation of the 3D Printability of Modified Starch-Based Inks and Their Formation Mechanism: Application in Ice Cream

Fabrication of Telechelic DNA-bridged Food Emulsion Gel As Edible Ink for 3D Printing

Processing and properties of aqueous protein/polysaccharide mixture-based inks for additive manufacturing

Development of soy protein isolate emulsion gels as extrusion-based 3D food printing inks: Effect of polysaccharides incorporation

Improvement of 3D printing performance of pea protein isolate Pickering emulsion gels by regulating electrostatic interaction between protein and polysaccharide

An Optimization Study of 3D Printing Technology Utilizing a Hybrid Gel System Based on Astragalus Polysaccharide and Wheat Starch

Fabrication of starch-based oleogels using capillary bridges: Potential for application as edible inks in 3D food printing

3D Printing Properties of Heat-Induced Sodium Alginate-Whey Protein Isolate Edible Gel

Citrus peel powder alters the rheological properties and 3D printing performance of potato starch gel

Three-dimensional (3D) printability assessment of food-ink systems with superfine ground white common bean (<i>Phaseolus vulgaris</i> L.) protein based on different 3D food printers

Fabrication of gelatin-based printable inks with improved stiffness as well as antibacterial and UV-shielding properties

Starch as edible ink in 3D printing for food applications: a review

Development, characterization and underling mechanism of 3D printable quinoa protein emulsion gels by incorporating of different polysaccharides for curcumin delivery

Three-Dimensional Printing Properties of Polysaccharide Hydrocolloids-Unrinsed Sturgeon Surimi Complex Hydrogels

Formulation and characterization of an interpenetrating network hydrogel of locust bean gum and cellulose microfibrils for 3D printing

Protein-stabilized Pickering emulsion interacting with inulin, xanthan gum and chitosan: Rheological behavior and 3D printing

Gelatin/polychromatic materials microgels enhanced by carnosic acid inclusions and its application in 2D pattern printing and multi-nozzle food 3D printing

Analysis on the printability and rheological characteristics of bigel inks: Potential in 3D food printing

Effects of gel spatial structure and water state on 3D printability: A case study of honey bee pupa protein and soybean dietary fiber

Depletion Attraction Driven Formation of Spirulina Emulsion Gels for 3D Printing