Abstract:This study utilizes a lab-developed pneumatic-extrusion condensing 3D food printer to prepare astragalus–starch mixed gels by blending different ratios of astragalus polysaccharide and wheat starch and applies these gels to 3D printing experiments. The aim of this paper is to investigate the impacts of mixed-gel concentrations on printing outcomes in order to identify the optimal blending ratio. Under this rationale, the effects of printing layer height and nozzle diameter on print quality were studied. Single-factor analysis and response surface methodology were employed to optimize the experiments and determine the optimal printing process parameters for the astragalus–starch mixed gels. The results indicate that an increase in astragalus polysaccharide content leads to a decrease in the sedimentation rate of the mixed gels and a tendency towards a more fluid consistency. After storage of samples in a sealed space for equal durations, it was found that an increase in astragalus polysaccharide content enhances the textural properties of the mixed gels, with optimal printing effects achieved at a 2% polysaccharide content. The optimal print quality is achieved when the ratio of nozzle diameter to layer height is between 0.5 and 0.55. The influence order of printing process parameters on the overall completion rate of the samples is nozzle diameter > printing speed > fill rate. The predicted optimal printing parameters are a nozzle diameter of 0.6 mm, a printing speed of 767 mm/min, and a fill rate of 83%, with a predicted overall completion rate of the printed samples at 99.45%. Experimental validation revealed an actual overall completion rate of the printed samples at 99.52%, slightly higher than the predicted value. This discrepancy was attributed to the precision of the measurement methods and the variability in the printing process. The study demonstrates that the addition of astragalus polysaccharide significantly improves the 3D printing molding effect of wheat starch, and the printing parameter settings obtained by response surface optimization effectively enhance printing accuracy. This research provides experimental evidence and parameter optimization references for the application of non-starch polysaccharides in starch-based 3D food printing.

Three-dimensional (3D) printability assessment of food-ink systems with superfine ground white common bean (Phaseolus vulgaris L.) protein based on different 3D food printers

Three-dimensional (3D) printability assessment of food-ink systems with superfine ground white common bean (<i>Phaseolus vulgaris</i> L.) protein based on different 3D food printers

A review on 3D printable food materials: types and development trends

Investigation of the 3D Printability of Modified Starch-Based Inks and Their Formation Mechanism: Application in Ice Cream

Improvement of 3D printing performance of pea protein isolate Pickering emulsion gels by regulating electrostatic interaction between protein and polysaccharide

Processing and properties of aqueous protein/polysaccharide mixture-based inks for additive manufacturing

Improving the Three-Dimensional Printability of Potato Starch Loaded onto Food Ink

Starch as edible ink in 3D printing for food applications: a review

Application of Protein in Extrusion-Based 3D Food Printing: Current Status and Prospectus

An Optimization Study of 3D Printing Technology Utilizing a Hybrid Gel System Based on Astragalus Polysaccharide and Wheat Starch

Faba Bean Fractions for 3D Printing of Protein-, Starch- and Fibre-Rich Foods

Advancements in 3D food printing: a comprehensive overview of properties and opportunities

3D Printing of Steak-like Foods Based on Textured Soybean Protein

3D bioprinting of low-viscosity phase-separated food-grade bioinks by in situ self-assembly

Preparation and characterization of 3D printed texture-modified food for the elderly using mung bean protein, rose powder, and flaxseed gum

Food-grade Pickering emulsions and high internal phase Pickering emulsions encapsulating cinnamaldehyde based on pea protein-pectin-EGCG complexes for extrusion 3D printing

Three-dimensional food printing: its readiness for a food and nutrition insecure world

3D Printing Properties of Heat-Induced Sodium Alginate-Whey Protein Isolate Edible Gel

Investigation of 3D printing of toddler foods with special shape and function based on fenugreek gum and flaxseed protein

Analysis on the printability and rheological characteristics of bigel inks: Potential in 3D food printing

The application of 3D printing technology on starch-based product: A review