Abstract:This study utilizes a lab-developed pneumatic-extrusion condensing 3D food printer to prepare astragalus–starch mixed gels by blending different ratios of astragalus polysaccharide and wheat starch and applies these gels to 3D printing experiments. The aim of this paper is to investigate the impacts of mixed-gel concentrations on printing outcomes in order to identify the optimal blending ratio. Under this rationale, the effects of printing layer height and nozzle diameter on print quality were studied. Single-factor analysis and response surface methodology were employed to optimize the experiments and determine the optimal printing process parameters for the astragalus–starch mixed gels. The results indicate that an increase in astragalus polysaccharide content leads to a decrease in the sedimentation rate of the mixed gels and a tendency towards a more fluid consistency. After storage of samples in a sealed space for equal durations, it was found that an increase in astragalus polysaccharide content enhances the textural properties of the mixed gels, with optimal printing effects achieved at a 2% polysaccharide content. The optimal print quality is achieved when the ratio of nozzle diameter to layer height is between 0.5 and 0.55. The influence order of printing process parameters on the overall completion rate of the samples is nozzle diameter > printing speed > fill rate. The predicted optimal printing parameters are a nozzle diameter of 0.6 mm, a printing speed of 767 mm/min, and a fill rate of 83%, with a predicted overall completion rate of the printed samples at 99.45%. Experimental validation revealed an actual overall completion rate of the printed samples at 99.52%, slightly higher than the predicted value. This discrepancy was attributed to the precision of the measurement methods and the variability in the printing process. The study demonstrates that the addition of astragalus polysaccharide significantly improves the 3D printing molding effect of wheat starch, and the printing parameter settings obtained by response surface optimization effectively enhance printing accuracy. This research provides experimental evidence and parameter optimization references for the application of non-starch polysaccharides in starch-based 3D food printing.

Effects of gel spatial structure and water state on 3D printability: A case study of honey bee pupa protein and soybean dietary fiber

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

Effect of Compositions and Physical Properties on 3D Printability of Gels from Selected Commercial Edible Insects: Role of Protein and Chitin.

Research on the Printability of Hydrogels in 3D Bioprinting.

A Strategy to Improve 3D Printing Performance: Interaction Between Epigallocatechin Gallate (EGCG) and Honey Bee Pupa Protein (HBPP)

Processing and performance of 3D‐printed gelatin‐based edible composite hydrogels

Digital Light Processing-Based 3D Printing of Cell-Seeding Hydrogel Scaffolds with Regionally Varied Stiffness

Effect of hybrid gelator systems of beeswax-carrageenan-xanthan on rheological properties and printability of litchi inks for 3D food printing

The Effect of Agarose on 3D Bioprinting

Formulation and characterization of an interpenetrating network hydrogel of locust bean gum and cellulose microfibrils for 3D printing

3D Printing Properties of Heat-Induced Sodium Alginate-Whey Protein Isolate Edible Gel

An Optimization Study of 3D Printing Technology Utilizing a Hybrid Gel System Based on Astragalus Polysaccharide and Wheat Starch

3D Printing of Soy Protein- and Gluten-Based Gels Facilitated by Thermosensitive Cocoa Butter in a Model Study

3D Printing Properties of Flammulina Velutipes Polysaccharide-Soy Protein Complex Hydrogels

Effects of Incubation Temperature on the Mechanical and Structure Performance of Beeswax-Carrageenan-xanthan Hybrid Gelator System in 3D Printing

Development and characterization of a casein-hyaluronic acid emulsion gel with high water-holding capacity and excellent rheological properties for 3D printing

Gelatin-Sodium Alginate Hydrogel Processing by Low-Temperature 3D Printing

Development of soy protein isolate emulsion gels as extrusion-based 3D food printing inks: Effect of polysaccharides incorporation

Rheological and mechanical behavior of milk protein composite gel for extrusion-based 3D food printing

Fabrication of Hydrogels with Adjustable Mechanical Properties Through 3D Cell-Laden Printing Technology

3D Printing Method for Tough Multifunctional Particle-Based Double-Network Hydrogels