Abstract:Heterogeneous microstructures such as macrozones and Widmannstätten microstructures are intolerable defects in high-temperature aero-engine parts manufactured using titanium (Ti) alloys. Through thermomechanical operations, microstructure characterization, phase reconstruction, and crystal plasticity finite element method (CPFEM) modeling, a full-route analysis was conducted to uncover the microstructure evolution of the allotropic β and α phases and the variant selection of the β→α phase transformation (PT) of a near-α Ti alloy. With an increase in temperature or decrease in strain rate, the continuous dynamic recrystallization (cDRX) of the β phase gradually prevails over the discontinuous dynamic recrystallization (dDRX) of the α phase. The reconstructed high-temperature β microstructure combing the CPFEM simulation revealed that the prior β grains with the deformation-induced 〈100〉//AD orientation, which are softer and grow preferentially via cDRX to form a simple cubic texture in the β phase. The coarse β phase transforms into the secondary α (αs) phase with a localized phase-transformed texture (the 1̅21̅0//AD and 101̅1//AD components) during the subsequent cooling process. Through the reconstructed β phase and crystallographic analysis of the β→α PT, we found that the low-angle grain boundary (LAGB) in the β phase weakens the anisotropic growth of αs grains and the preferential variant selection of 1̅21̅0/60° αs/αs grain boundary (GB) caused by autocatalytic nucleation. A high strain-rate deformation can increase the intragranular defects (e.g., LAGB) of the β phase, which promote the formation of a basket-weave structure instead of a Widmannstätten structure and weakens the variant selection during β→α PT.

Three-dimensional morphology of tri-modal microstructure and evolution mechanisms of constitute phases in dual heat treated near-α titanium alloy

Formation and characteristics of bilamellar microstructure in Ti6242S titanium alloy under dual heat treatment

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

Microstructure Evolution of Near-Α Titanium Alloys During Thermomechanical Processing

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Formation mechanism of lamellar bimodal microstructure and mechanical property in the high temperature near α titanium alloy

EBSD Study on Dual Heat Treatment and Microstructure Evolution of TA15 Titanium Alloy

Effect of Third-Stage Heat Treatments on Microstructure and Properties of Dual-Phase Titanium Alloy

Phase transformation mechanisms, microstructural characteristics and mechanical performances of an additively manufactured Ti-6Al-4V alloy under dual-stage heat treatment

Preparation of Multiscale α Phase by Heat Treatments and Its Effect on Tensile Properties in Metastable β Titanium Alloy Sheet

Enhanced strength of dual-phase Ti6242 alloy via a heterogeneous microstructure

Formation mechanism of lamellae during ¡ transformation in polycrystalline dual-phase Ti alloys

Effect of α+β phase rolling and aging treatment on laminated bimodal structure in high temperature titanium alloy

Relationship Between Microstructure and Tensile Properties on a Near-Β Titanium Alloy after Multidirectional Forging and Heat Treatment

Effect of thermo-mechanical processing on microstructure and mechanical properties of near α titanium alloys

Heterogeneous Precipitate Microstructure in Titanium Alloys for Simultaneous Improvement of Strength and Ductility

α′′ phase-assisted nucleation to obtain ultrafine α precipitates for designing high-strength near-β titanium alloys

Sensitivity of Heterogeneous Microstructure Evolution and Preferential Variant Selection to Thermomechanical Conditions in a Near Α Titanium Alloy

Phase Transformation During Continuous Heating in a Β-Quenched Ti-5Al-3Mo-3V-2Cr-2Zr-1Nb-1Fe Alloy

Microstructure Evolution and Nano-Precipitate of Multi-Stage Heat-Treated Ti–45Al–2Nb–2Cr-0.3C Alloy

Microstructure Evolution and Phase Transformations in Ti-22Al-25Nb Alloys Tailored by Super-Transus Solution Treatment