Abstract:Surface preparation of ultra-high modulus fiber composites for adhesive bonding is challenging due to the subsurface damages that can occur during a standard abrasion operation that could weaken the laminate cohesion. Therefore, it is highly desirable to utilize a non-contact method that can clean and activate the composite surface without exerting an external force to eliminate potential damage. This investigation focuses on the use of atmospheric plasma treatment (APT) for the surface preparation of unidirectional ultra-high modulus, composites for adhesive bonding. The laminates were manufactured using Mitsubishi K13C2U pitch-based carbon fiber with Tencate's RS-3C cyanate-ester resin and bonded with Henkel 9394 epoxy. Surface analysis of plasma-treated samples revealed a significant reduction of surface contamination and increased chemical modification of the matrix material resulting in improved wetting and the formation of chemical groups conducive to bonding. The plasma treatment also produced a minor increase in surface roughening, well below levels expected to contribute to mechanical interlocking. APT epoxy-bonded lap-shear specimens (LSS) exhibited a 50% increase in strength as compared to mechanically abraded samples. It was also shown that solvent rinsing after APT removed a highly-oxidized, poorly bonded carbonate component from the treated resin surface as evidenced by XPS. This surface ash is observed at fairly high concentrations after APT of cyanate ester resin composites limiting functional group contributions. The removal of this ash resulted in increases in LSS of 25% as compared to unrinsed APT surfaces. Lap shear strengths and GIC delamination resistance tests showed improvements over abrasion surface treated samples. Image analysis of the fracture faces for both surface treatments showed that abrasion treated surfaces resulted in sub-surface damage to the fibers that translated into brittle fracture through weak, highly aligned layers within these graphitic fibers. On the other hand, plasma treatment was successfully applied to minimize subsurface damage and resulted in crack propagation along with the more tortuous fiber-matrix interface. The degree of the improvements was ultimately limited by the interlaminar strength of these composites.

Interface Engineering via Non-Thermal Atmospheric Plasma for Highly Tensile Insulating Epoxy-Impregnated Aramid Composite Paper

Enhancing CFRP Laminates with Plasma Jet Arrays: A Study of Interlaminar Mechanical Properties

Enhanced Insulation Strength of Meta-Aramid Paper by Co-Modification of Chopped Fiber With Plasma Discharge and Coupling Agent

Impact of defect structures on interfacial and insulation properties in epoxy-impregnated aramid paper

Effects of Air Plasma Modification on Aramid Fiber Surface and Its Composite Interface and Mechanical Properties

Improved dielectric and mechanical properties of aramid fiber reinforced epoxy resin composites by polyethyleneimine grafting

Effects of argon plasma treatment on carbon fiber surface characteric and its reinforcing polyimide composites interfacial properties at room and elevated temperatures

Surface Modification of Aramid Fiber by Cascade Process with Atmospheric Plasma and TDI Grafting

Preparation of highly active aramid fiber and effect on the interface property of aramid/epoxy composites

Enhanced in-plane thermal conductivity of polyimide-based composites via in situ interfacial modification of graphene

Aramid Nanofibers at Ultralow Loadings: Driving Significant Multifunctionality in Epoxy Composite Dielectrics

Investigations on the effect of plasma treatment on the adhesive bonding behavior of ultra high modulus K13C2U/cyanate ester fiber composites

Strengthening the Interface Between Individual Aramid Fibers and Polymer at Room and Elevated Temperatures

Interface failure identification of argon/nitrogen double plasma modified hybrid laminated para‐aramid composites

Enhanced interfacial adhesion of aramid fiber III reinforced epoxy composites via low temperature plasma treatment

Interfacial studies on the surface modified aramid fiber reinforced epoxy composites

Tuning Interfacial Characteristics of Epoxy Composites Towards Simultaneous High Thermal and Dielectric Properties

Preparation and Performance Study of Composite Aramid Paper for High Frequency Working Conditions

Enhancing Mechanical Strength of Carbon Fiber-Epoxy Interface Through Electrowetting of Fiber Surface

Surface modification of aramid fiber by crystalline polyarylene ether nitrile sizing for improving interfacial adhesion with polyarylene ether nitrile

Introducing deep trap states for high dielectric strength of aramid‐based composite films