Abstract:Heavy metal-based vehicle caused increase in fuel consumption, which creates pollution in the environment; thus, scientists across the nation researched to produce light weight, cost-effective, easy degradable, corrosive resistant composite material. Due to such features present in the composite material, the present research aims to examine the impact of alkali-silane treatment on the time-dependent and machining behavior of composites. Further, the alkali treatment and silane treatment on fiber and filler particle are carried out to provide even dispersion of filler particle and better reinforcement and interfacial bonding adhesion to the composite material, which makes a novelty to this study. The obtained fiber and filler particle were reinforced to matrix by using hand layup method and subsequently cured. This prepared composite material's strength is analyzed as per the ASTM standards. The results indicate that the inclusion of surface modified corn-fiber reinforced EF composite shows stronger interfacial adhesion, which implies loss factor of 42.8% lower than neat epoxy. Similarly, reinforcing corn husk fiber increases the energy release rate by 2500% and the fracture toughness by 156.47% when compared to pure epoxy composite. Further, the inclusion of biosilica particle of 2.0 vol.% exhibited the highest storage modulus of 5.69 GPa and the lowest loss factor of 0.32. This demonstrates the beneficial effect of combining alkali and silane treatment on corn fiber and filler particle. The epoxy composite (EFP3) of chemically treated fiber 30 vol.% and 2 vol.% of biosilica reinforcement exhibits a higher fatigue life cycle, fracture toughness, and energy release rate of 30,546, 26.5 MPa√m, and 0.86 MJ/m 2 , respectively. Similarly, the composite designation EFP3 has the lowest contact angle of 78°, indicating the preserved hydrophobicity. A drilling study has shown that using a 4-mm drill bit and 8-mm drill bit. The resultant of the drilling studies concludes that the use of 2.0 vol.% biosilica reduced the occurrence of fiber pull-out while drilling. Owing to such improved strength properties, light weight, corrosive resistant features in the biocomposite are applied in industries such as automotive, sporting goods, food and drug packaging, aerospace, and other technical applications that require strong load-bearing capacity, etc.

Development of almond shell powder and palm kernel fibre–reinforced cardanol oil toughened epoxy resin hybrid composites: mechanical, wear, and antimicrobial properties

Mechanical, thermal, and fatigue behavior of aloe vera fiber/pistachio shell powder toughened epoxy resin composite

A comprehensive experimental study of eco-friendly hybrid polymer composites using pistachio shell powder and Aquilaria agallocha Roxb

Development of silane-treated corn husk fiber and agro-waste biofiller-reinforced epoxy composite: effects on wear, mechanical, thermal, and water absorption properties

Mechanical, Wear and Fatigue Behaviour of Neem Oil and Nanosilica Toughened Areca Fibre Reinforced Epoxy Resin Composite

Investigation on Interlaminar Shear Strength and Moisture Absorption Properties of Soybean Oil Reinforced with Aluminium Trihydrate-Filled Polyester-Based Nanocomposites

Valorisation of corn waste as fiber, biosilica, and their epoxy composites: fatigue, fracture toughness, water absorption, and drilling properties

Experimental investigation on the mechanical and wear behavior of epoxy/Indian almond/peepal hybrid composites

Effect of alumina fillers on physical and mechanical properties of luffa/groundnut shell natural fiber reinforced polymer composites

Mechanical, morphological and wear resistance of natural fiber / glass fiber-based polymer composites

Flame retardant, load bearing and thermal studies on satin weaved sunn hemp fibre and cashew nut shell de-oiled cake biosilica epoxy composites

Enhancing the Bio-epoxy Composites with Oil Palm Fibre as Reinforcement: Assessment of Mechanical, Physical and Thermal Properties

Visco-Elastic, Thermal, Antimicrobial and Dielectric Behaviour of Areca Fibre-Reinforced Nano-silica and Neem Oil-Toughened Epoxy Resin Bio Composite

Investigation on the mechanical, water absorption, and tribological performance of calotropis gigantea and abaca fiber reinforced epoxy composites

Mechanical (Static and Dynamic) Characterization and Thermal stability of hybrid green composites for Engineering Applications

Effect of snail shell powder addition on mechanical and microstructure behaviour of mercerized roselle fiber reinforced epoxy resin-based hybrid composite

Enhancing mechanical, thermo-mechanical and low velocity impact properties of epoxy methyl ricinoleate toughened epoxy composites by integrating microcrystalline cellulose

Influence of silica and alumina nanoparticles on the wear and mechanical behavior of Indian almond fiber reinforced natural composites

Effect of silane treatment on corn husk and tamarind fiber and betel nut filler on fatigue, thermal conductivity, and machining behavior of epoxy biocomposites

Enhanced Morphological and Thermal Properties of Epoxy Composites Reinforced with Palm and Prosopis Juliflora Fibers

Influencing Behavior Study of Natural Almond Shell Filler on the Tensile, Thermal, and Free Vibrational Properties of Flax Fiber Intertwined Vinyl Ester Composites