Abstract:Heavy metal-based vehicle caused increase in fuel consumption, which creates pollution in the environment; thus, scientists across the nation researched to produce light weight, cost-effective, easy degradable, corrosive resistant composite material. Due to such features present in the composite material, the present research aims to examine the impact of alkali-silane treatment on the time-dependent and machining behavior of composites. Further, the alkali treatment and silane treatment on fiber and filler particle are carried out to provide even dispersion of filler particle and better reinforcement and interfacial bonding adhesion to the composite material, which makes a novelty to this study. The obtained fiber and filler particle were reinforced to matrix by using hand layup method and subsequently cured. This prepared composite material's strength is analyzed as per the ASTM standards. The results indicate that the inclusion of surface modified corn-fiber reinforced EF composite shows stronger interfacial adhesion, which implies loss factor of 42.8% lower than neat epoxy. Similarly, reinforcing corn husk fiber increases the energy release rate by 2500% and the fracture toughness by 156.47% when compared to pure epoxy composite. Further, the inclusion of biosilica particle of 2.0 vol.% exhibited the highest storage modulus of 5.69 GPa and the lowest loss factor of 0.32. This demonstrates the beneficial effect of combining alkali and silane treatment on corn fiber and filler particle. The epoxy composite (EFP3) of chemically treated fiber 30 vol.% and 2 vol.% of biosilica reinforcement exhibits a higher fatigue life cycle, fracture toughness, and energy release rate of 30,546, 26.5 MPa√m, and 0.86 MJ/m 2 , respectively. Similarly, the composite designation EFP3 has the lowest contact angle of 78°, indicating the preserved hydrophobicity. A drilling study has shown that using a 4-mm drill bit and 8-mm drill bit. The resultant of the drilling studies concludes that the use of 2.0 vol.% biosilica reduced the occurrence of fiber pull-out while drilling. Owing to such improved strength properties, light weight, corrosive resistant features in the biocomposite are applied in industries such as automotive, sporting goods, food and drug packaging, aerospace, and other technical applications that require strong load-bearing capacity, etc.

Effect of silane treatment on corn husk and tamarind fiber and betel nut filler on fatigue, thermal conductivity, and machining behavior of epoxy biocomposites

Valorisation of corn waste as fiber, biosilica, and their epoxy composites: fatigue, fracture toughness, water absorption, and drilling properties

Development of silane-treated corn husk fiber and agro-waste biofiller-reinforced epoxy composite: effects on wear, mechanical, thermal, and water absorption properties

Effect of silane-treated lignin and hybrid bamboo-green pea sheath fiber on mechanical, wear, and wettability behavior of epoxy structural composite

Load-Bearing and Machining Behavior of Treated Nano-sorghum-Millet-Husk-Biosilica- and Kenaf-Fiber-Reinforced Vinyl Ester Composite

Effect of Amino Silane Grafted Cellulose and Kenaf Fibers in Mechanical, Impact Toughness and Drilling Characteristics of Epoxy Resin Composite

Characterization of heat-treated rice husk Si3N4 bioceramic on cellulosic corn husk fiber-polyester composite

Experimental Investigations of Epoxy Biocomposites Developed Using Alkali-Silane treated Cellulosic Corn Husk Fiber and Corn Cob Biosilica

Mechanical, wear and fatigue behavior of silane‐treated corncob biosilica toughened epoxy resin composite reinforced with prickly pear short fibers

Characterization of heat-treated biosilica from biomass waste fox tail millet husks and banana fiber reinforced epoxy composite

Mechanical, Wear and Fatigue Behaviour of Neem Oil and Nanosilica Toughened Areca Fibre Reinforced Epoxy Resin Composite

Experimental evaluation and comparison of silica/biocarbon particulate-epoxy composites for high-strength applications

Effect of bio nanofiller in influencing the carbon and E-glass fabric reinforced composites

Effect of palmyra sprout fiber and biosilica on mechanical, wear, thermal and hydrophobic behavior of epoxy resin composite

Low Velocity Impact and Mechanical Behaviour of Shot Blasted SiC Wire-Mesh and Silane-Treated Aloevera/Hemp/Flax-Reinforced SiC Whisker Modified Epoxy Resin Composites

Impact of different parameters in tribological properties of enset ventricosum/ terminalia arjuna fibers /SiO 2 filler incorporation

Thermal Conductivity and Mechanical Characterization of Bamboo Fiber and Rice Husk/MWCNT Filler Epoxy Hybrid Composite

Effect of hybridization of novel African teff and snake grass fibers reinforced epoxy composites with bio castor seed shell filler: Experimental investigation

Treated sisal fiber made epoxy composite hybridize with silicon carbide nanoparticles: Characteristics study

Studies on mechanical and water absorption behavior of biofiber-reinforced epoxy biocomposites added with seashell, eggshell, and coconut biofillers

Effect of rice husk ash silicon nitride on mechanical, wear, thermal conductivity, and flammability behavior of aluminized glass-kenaf fiber-reinforced polyester composite