Abstract:A Ni‐based interlayer alloy is designed for transient liquid phase bonding of ZGH451 superalloy produced through directed energy deposition. Joints with a controlled gap within the range of 0–30 μm achieve complete isothermal solidification, exhibiting up to 1375 MPa tensile strength at room temperature and 983 MPa at 760 °C. Notably, the interlayer alloy developed in this study outperforms the conventional BNi‐2. ZGH451, a directionally solidified Ni‐based superalloy designed for additive manufacturing, has garnered significant attention in the realm of next‐generation turbine blades. Welding the ZGH451 superalloy is crucial for promoting its practical application. In this study, transient liquid phase (TLP) bonding is applied to weld ZGH451 superalloy produced through directed energy deposition. A Ni‐based interlayer alloy powder is developed and prepared via thermodynamic calculation, with the interlayer subsequently characterized using differential thermal analysis. TLP bonding is conducted at 1200 °C for 4 h. The influence of the preset gap on the joint microstructure and mechanical properties is examined. The microstructure of the TLP bonding joints comprises athermally solidified zones (ASZ), isothermally solidified zones, and diffusion‐affected zones. The ASZ width significantly increases with the growing preset gap. A preset gap not exceeding 100 μm enables complete isothermal solidification of the joints. Particularly, joints with a preset gap ranging from 0 to 30 μm demonstrate optimal reliability, exhibiting a tensile strength of up to 1375 MPa at room temperature, which is 12% higher than the room temperature strength of the base metal (BM), and a tensile strength of 983 MPa at 760 °C, surpassing 86% of the BM's strength at the same temperature.

Transient Liquid Phase Bonding of Hastelloy X to Ni 3 Al Intermetallic Compound: Microstructure and Phase Transformation Study

Phase Formation during Heating of Amorphous Nickel-Based BNi-3 for Joining of Dissimilar Cobalt-Based Superalloys

Intermetallic phase formation during brazing of a nickel alloy using a Ni–Cr–Si–Fe–B quinary filler alloy

Role of Nanostructured Ni Surface Layer in Enhanced Hastelloy Alloy Diffusion Bonding at Temperatures Far Beyond Recrystallization

Transient Liquid Phase Bonding of Nickel-Base Single Crystal Alloy with a Novel Ni-Cr-Co-Mo-W-Ta-Re-B Amorphous Interlayer

Transient Liquid Phase Bonding of Cast Al0.3CoCrFeNi High-Entropy Alloy Using Ni/Zr/Ni Laminated Foils

The Microstructures and Mechanical Properties of a Welded Ni-Based Hastelloy X Superalloy

Transient Liquid Phase Bonding of IC10 Single Crystal with GH3039 Superalloy Using BNi2 Interlayer: Microstructure and Mechanical Properties

Transient Liquid Phase Diffusion Bonding of Ni3Al Superalloy with Low-Boron Nickel-Base Powder Interlayer

Effect of transient liquid phase bonding followed by homogenization on the microstructure and hot tensile behavior of Inconel 738 superalloy

Microstructure and Mechanical Properties of Ni3Al-based Alloy Joint Transient Liquid Phase Bonded Using Ni/Ti Interlayer

Evolution of microstructure and mechanical properties on dissimilar transient liquid phase (TLP) bonding of GTD-111 and IN-718 by BNi-9 (AWS A5.8/A5.8M) interlayer

Development of Transient Liquid Phase Bonding of Ni-base Superalloy, Inconel 718 to Skip Homogenising Heat Treatment

Microstructure Evolution and Mechanical Properties of Transient Liquid Phase (TLP) Bonded Joints of TiAl Intermetallics

Experimental and Numerical Study of Transient Liquid Phase Diffusion Bonded DZ40M Superalloys

Transient Liquid Phase Bonding of ZGH451 Superalloy Fabricated by Directed Energy Deposition

Effect of holding time on microstructure and mechanical properties of dissimilar γ'‐strengthened superalloys TLP joint

Effect of bonding time, composition of interlayer and post bond heat treatment on TLP joints of Inconel 718 superalloy

Diffusion Brazing of GH536 Polycrystalline Superalloy with IC10 Single Crystal Superalloy Using BNi-2 Interlayer

Transient Liquid Phase Bonding of Inconel 718 With Ni and BNi-2 Nano-Braze Materials

Microstructural Evolution of Post-Processed Hastelloy X Alloy Fabricated by Laser Powder Bed Fusion