Abstract:Secondary lithium-ion batteries have been widely used as energy storage systems for portable electronics and electric vehicles. Instead of applying graphite as the anode, lithium (Li) metal has an ultrahigh theoretical capacity (3860 mAh/g) that could significantly increase battery’s energy density. Li dendrite formation is considered the main issue when using Li-metal anodes. Therefore, anode-free batteries are suggested as a solution to this obstacle. However, the major problem with anode-free batteries is their inferior cycling performance than reported lithium metal batteries, resulting from the formation of a fragile and fractured Solid-Electrolyte Interphase (SEI). To establish a robust SEI, novel lithium bis(trifluoromethylsulphonyl)imide (LiTFSI) and LiNO 3 -based electrolytes with four different ratios were prepared in the co-solvent system (1,3-dioxolane and 1,2-dimethoxyethane). Compared to the other three electrolytes, concentrated electrolyte (4M LiTFSI + 2 wt.% LiNO 3 or 4+2) in Li||LiFePO 4 cells indicated the highest initial discharge capacity of 154 mAh/g with a capacity retention of 78% after 50 cycles. Scanning electron microscopy was conducted to investigate the SEI morphology after the initial charge/discharge process. The deposited Li on the Li metal was highly dense, and no spiky or needle-like Li clusters were detected. Additionally, electrochemical impedance spectroscopy of the cells was measured after 1, 3, 5, and 10 cycles, respectively. The cells with 4+2 showed the smallest SEI resistance after different cycles, corresponding to a stable and less-resistive SEI formation.

Concentrated precipitation electrolyte for reviving ultrathin lithium metal anode

Concentrated Electrolyte for Stable Lithium Metal Anode

A Bifunctional Composite Artificial Solid Electrolyte Interphase for High Stable Solid-State Lithium Batteries

In Situ Constructing a Stable Solid Electrolyte Interface by Multifunctional Electrolyte Additive to Stabilize Lithium Metal Anodes for Li-S Batteries

An Inorganic‐Rich Solid Electrolyte Interphase for Advanced Lithium‐Metal Batteries in Carbonate Electrolytes

Pseudo-concentrated Electrolytes for Lithium Metal Batteries

A Concentrated Ternary‐Salts Electrolyte for High Reversible Li Metal Battery with Slight Excess Li

An artificial layer enables in situ generation of a homogeneous inorganic/organic composite solid electrolyte interphase for stable lithium metal batteries

Constructing an Inorganic-Rich Solid Electrolyte Interphase by Adjusting Electrolyte Additives for Stable Li Metal Anodes

Regulation of SEI Formation by Anion Receptors to Achieve Ultra‐Stable Lithium‐Metal Batteries

Ultra‐Low Concentration Electrolyte Enabling LiF‐Rich SEI and Dense Plating/Stripping Processes for Lithium Metal Batteries

Electrolyte engineering for highly inorganic solid electrolyte interphase in high-performance lithium metal batteries

A Lithiophilic Interphase Enabled by Thiophenol Additive for Stable Lithium Metal Anode

Anion-derived solid electrolyte interphase realized in usual-concentration electrolyte for Li metal batteries

Uniform High Ionic Conducting Lithium Sulfide Protection Layer for Stable Lithium Metal Anode

Self‐Induced Dual‐Layered Solid Electrolyte Interphase with High Toughness and High Ionic Conductivity for Ultra‐Stable Lithium Metal Batteries

Bi-containing Electrolyte Enables Robust and Li Ion Conductive Solid Electrolyte Interphase for Advanced Lithium Metal Anodes

Organophosphorus Hybrid Solid Electrolyte Interphase Layer Based on LixPO4 Enables Uniform Lithium Deposition for High‐Performance Lithium Metal Batteries

A Facile Way to Construct Stable and Ionic Conductive Lithium Sulfide Nanoparticles Composed Solid Electrolyte Interphase on Li Metal Anode

Constructing a conductive solid electrolyte interface by adding lithium nitrate into carbonate electrolyte for stable lithium metal anode

Solvent-derived Inorganic F and N-rich Solid Electrolyte Interface for Stable Lithium Metal Batteries