Abstract:Bisphenol A dicyanate (BADCy) resin microparticles were prepared by precipitation polymerization synthesis and were homogeneously dispersed in a BADCy prepolymer matrix to prepare a BADCy self-reinforced composites. The active functional groups of the BADCy resin microparticles were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results of an FT-IR curve showed that the BADCy resin microparticles had a triazine ring functional group and also had an active reactive group -OCN, which can initiate a reaction with the matrix. The structure of the BADCy resin microparticles was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the TEM results, the BADCy resin microparticles dispersed in the solvent were nano-sized and distributed at 40-60 nm. However, from the SEM results, agglomeration occurred after drying, the BADCy resin particels were micron-sized and distributed between 0.3 μm and 0.6 μm. The BADCy resin prepolymer was synthesized in our laboratory. A BADCy self-reinforced composite was prepared by using BADCy resin microparticles as a reinforcement phase. This corresponds to a composite in which the matrix and reinforcement phase are made from different morphologies of the same monomer. The DSC curve showed that the heat flow of the microparticles is different from the matrix during the curing reaction, this means the cured materials should be a microscopic two-phase structure. The added BADCy resin microparticles as reaction sites induced the formation of a more complete and regular cured polymer structure, optimizing the cross-linked network as well as increasing the interplay between the BADCy resin microparticles and prepolymer matrix. Relative to the neat BADCy resin material, the tensile strength, flexural strength, compressive strength and impact strength increased by 98.1%, 40.2%, 27.4%, and 85.4%, respectively. A particle toughening mechanism can be used to explain the improvement of toughness. The reduction in the dielectric constant showed that the cross-linked network of the self-reinforced composite was more symmetrical and less polar than the neat resin material, which supports the enhanced mechanical properties of the self-reinforced composite. In addition, the thermal behavior of the self-reinforced composite was characterized by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results of DMTA also establishes a basis for enhancing mechanical properties of the self-reinforced composite.

Study on the effect of porosity on properties of cyanate ester composites

Effects of different treatments on the interface and mechanical properties of high density polyethylene reinforced by sericite-tridymite-cristobalite

Study on Co-curing Behavior and their Laminate Properties of Low Bromined Epoxy/Cyanate Blends

Enhanced Interfacial, Mechanical, and Anti-Hygrothermal Properties of Carbon Fiber/cyanate Ester Composites with the Catalytic Sizing Agents of Titanium Epoxy

Study on Toughness and Dielectric Property of Modified Cyanate Ester Resin

Hygrothermal-resistant epoxy cured by cyanate and its composites

Study on Properties of 5528 Cyanate Resin

Effects of various porosities on the damage evolution behavior of carbon fiber/epoxy composites using acoustic emission and micro-CT

Study on Properties of 5528 Cyanate Resin Matrix GFRP

Evaluation of porosity effects on the mechanical properties of carbon fiber-reinforced plastic unidirectional laminates by X-ray computed tomography and mechanical testing

Hydrolysis susceptibility and carbamate formation for a low moisture-absorbing, siloxane-modified cyanate ester resin matrix (TC410) material used for composite space applications

Research on properties of composite based on polyether sulfone/cyanate ester semi‐interpenetrating resin system

Study on the Relationships between Microscopic Cross-Linked Network Structure and Properties of Cyanate Ester Self-Reinforced Composites

Ameliorated Mechanical and Dielectric Properties of Heat-Resistant Radome Cyanate Composites

Investigation on Mechanical Properties and Thermal Expansibility of Epoxy Resin Copolymerization Modified Cyanate Ester under Medium‐low Temperature Curing Process

Influences of particle content, size and particle/matrix bonding strength on the gas transmission coefficient of carbon fiber reinforced epoxy

Effect of Electrochemical Aryl Diazonium Salt Modification on Interfacial Properties of CF/PEEK Composites

Hybrid Network Structure And Mechanical Properties Of Rodlike Silicate/Cyanate Ester Nanocomposites

The curing kinetics and mechanical properties of epoxy resin composites reinforced by PEEK microparticles

Cyanate ester resin based composites with high toughness and thermal conductivity

The Study on Poly(ether Sulfone) Modified Cyanate Ester Resin and Epoxy Resin Cocuring Blends