Abstract:It is necessary to fabricate (RE)BCO bulk high temperature superconductors in the form of individual single grains in order to maximise the length scale over which current flows, and hence trapped magnetic field. However, inherent difficulties in the grain growth process place limitations on the diameter and height of the single grain that may be achieved by existing melt processes. A practical approach to increase the height of the sample and the trapped field at its surface is by assembling individual single grains in a stack formation with their ab planes aligned parallel, primarily to avoid the expensive process of fabricating large, individual monoliths. The trapped fields observed at the top and bottom surfaces of a single grain sample are frequently different since both the superconducting and physical properties of single grain (RE)BCO samples are generally non-uniform. This leads to challenges in determining how to arrange spatially stacks of single grain samples to generate the largest and most uniform trapped field overall. In this study we report the optimisation of two-stack configurations involving a total of 8 individual GdBCO/Ag single grains. The samples were arranged in four pairs and configured with different surfaces in contact in the assembly of the stack. The primary superconducting properties for trapped field and total flux applications were measured at 77 K and compared for each stack arrangement. The initial results indicate that surfaces with inferior flux trapping properties (measured in terms of the overall trapped field value) of a two-sample stack should be positioned at the middle of the assembly toachieve the best overall trapped field and higher total flux at the external, and therefore, usablesurface of the stack sample. A numerical modelling method that incorporates different Jc-Bcharacteristics for the top and bottom layers of a single grain to take account of the variability inphysical properties and spatial non-uniformity confirmed the optimised experimental arrangement of the stacked bulk samples. Furthermore, the optimisation of single grains of ring geometry to achieve a longer and wider uniform magnetic field zone inside the bore was also performed.

Crossed fields magnetization of YBCO single-grain bulk superconductors

Comparative calculations of trapped field and trapped magnetic flux with different multi-pulse magnetization methods for a bulk high-temperature superconductor

Behavior of bulk high-temperature superconductors of finite thickness subjected to crossed magnetic fields

Electromagnetic and Thermal Properties of HTS Bulk Combined With Different Ferromagnetic Structures Under Pulsed Field Magnetization

Remagnetization of bulk high-temperature superconductors subjected to crossed and rotating magnetic fields

Simulation of High Temperature Superconducting Bulks Magnetized by Pulsed Field Magnetization with an Electromagnetic-Thermal Coupled Model

A Pulsed Current Charging Mechanism for High Temperature Superconducting Magnets

Pulsed field magnetization of 0°–0° and 45°–45° bridge-seeded Y–Ba–Cu–O bulk superconductors

Simulation and experiments of Stacks of High Temperature Superconducting Coated Conductors Magnetized by Pulsed Field Magnetization with Multi-Pulse Technique

Pulse Field Magnetization of GdBCO without Rapid Decrease in Magnetic Flux Density

Review on high-temperature superconducting REBCO trapped field magnets

Magnetic moment and local magnetic induction of superconducting/ferromagnetic structures subjected to crossed fields: experiments on GdBCO and modelling

The Conceptual Optimal Design of a 300MJ High Temperature Superconducting Magnet

Influence of soft ferromagnetic sections on the magnetic flux density profile of a large grain, bulk Y–Ba–Cu–O superconductor

Optimisation of stacked, bulk high temperature superconductors for trapped-field magnet applications

Analysis of mechanical behavior in inhomogeneous high-temperature superconductors under pulsed field magnetization

Simulation of Stacks of High Temperature Superconducting Coated Conductors Magnetized by Pulsed Field Magnetization Using Controlled Magnetic Density Distribution Coils

Reliable 4.8 T trapped magnetic fields in Gd–Ba–Cu–O bulk superconductors using pulsed field magnetization

Superconducting Bulk Magnets: Very High Trapped Fields and Cracking

Effect of seed orientations on the crystallization characteristics and the magnetic levitation properties of single domain YBCO bulk superconductors

Practical technique of pulsed field magnetization for bulk HTS application