Abstract:To enable the success of solid-state stamp forming of unidirectional fibre reinforced thermoplastics (UD FRTPs), it is essential to accurately characterise and model the material deformation under desired conditions. This paper comprehensively investigates the intra-ply tensile and shear properties of unidirectional carbon fibre reinforced polyamide 6 (UD CF/PA6), which is a type of commonly used UD FRTP. To accomplish this, tensile and V-Notched Rail (VNR) shear tests are conducted for characterising the intra-ply transverse tensile and longitudinal shear properties, respectively. The temperature effects (180 – 220 °C, at 0.01 /s for the transverse tensile deformation and at 0.04 /s for longitudinal shear deformation) and strain-rate effects (0.001 – 0.25 /s for transverse tensile deformation and 0.004 – 0.4 /s for the longitudinal shear deformation, both are at 200 °C) are studied. It is found that temperature has significant effects on the intra-ply deformation properties, while the strain-rate effects are marginal. This paper also proposes a new physically based constitutive model considering all the deformable constituents, i.e., the polymer constituent reinforced by fibres (PrF) and the polymer-fibre interface (P-F). This model not only shows good prediction of the thermomechanical properties of UD CF/PA6 under intra-ply deformations, but also gives insights into the deformation mechanisms. The new physically based constitutive model is successfully embedded into Finite Element Analysis (FEA) software and validated through accurate prediction of intra-ply deformation of a CF/PA6 specimen under bias-extension. The methodologies and model developed here offer an effective tool for predicting the intra-ply deformation behaviours and guiding the solid-state stamp forming process of UD FRTPs.

Characterizing the Stress Relaxation Behavior of Unidirectional Prepreg through a Parallel Fractional-Order Viscoelastic Model

Modeling and experimental validation of compaction pressure distribution for automated fiber placement

Numerical simulation analysis of forming of continuous fiber reinforced polypropylene composites: Relaxation, creep, and hot stamping

A fractional model with parallel fractional Maxwell elements for amorphous thermoplastics

Characterization of Inter-Ply Slipping Behaviors in Hot Diaphragm Preforming: Experiments and Modelling

Deformation and Fracture Mechanisms of Automated Fiber Placement Pre-Preg Laminates under Out-of-plane Tensile Loading

Research on Modeling of Hot Embossing Polymeric Microfluidic Chip

A viscoelastic-plastic model for the temperature-dependent creep and recovery behavior during dry fiber fabric compaction

Constitutive modeling of stress relaxation for fabric reinforced rubber composites

A hybrid lamination model for simulation of woven fabric reinforced thermoplastic composites solid-state thermo-stamping

A dual‐scale three‐dimensional thermo‐viscoelastic model for the hot stamping simulation of thermoplastic composites

Analysis and modeling of the mechanical behavior of the compaction process of flexible guided 3D weaving

Micromechanical Modeling of Viscoplastic Behavior of Laminated Polymer Composites with Thermal Residual Stress Effect

Temperature-Dependent modelling of tension, in-Plane shear, and bending behaviour in non-isothermal thermo-Stamping process simulation of unidirectional UHMWPE fibre reinforced thermoplastic TPU composites

Validation of shape change predictions for stamp forming of carbon fiber thermoplastic composite laminates

A three-dimensional viscoelastic analysis of thermoplastic resin matrix composite laminates during hot stamping

A Novel Model for Predicting Deformation of Thermoplastic Composites During Heat-Pressing Process

Development and Verification of a Finite Element Model for Double Diaphragm Preforming of Unidirectional Carbon Fiber Prepreg

A Lamination Model for Forming Simulation of Woven Fabric Reinforced Thermoplastic Prepregs

Experimental characterisation and constitutive modelling of the intra-ply tensile and shear properties of unidirectional fibre reinforced thermoplastics (UD FRTPs) under solid-state stamp forming conditions

Ply-ply Friction Behavior Between Unidirectional Thermoplastic Prepreg Plies During Thermoforming: Characterization and Modeling