Abstract:In this study, a thermo-mechanical finite element model was developed to investigate the thermal deformation during a stamping process of an automotive body part. The stamping process was decomposed into the 6 sub-steps to reflect the physical boundary conditions found in an actual stamping equipment. The temperature distributions of the actual stamping process were measured by two thermography cameras. The developed numerical procedure was then validated against the measured temperature distributions. Due to the limited accessibility to the actual equipment and high reflectivity of the involved material, the reflectivity index for the thermal imaging device (i.e., emissivity) was experimentally determined. A sample specimen made of the same material with the die material was built. The thermocouples were placed underneath the specimen surface through holes and used to directly measure the surface temperature distribution. The emissivity for the sample specimen was then determined by comparing the temperature measured by the thermocouples to the temperature measured by the thermographic camera. When the lubrication oils were spread on the sample specimen, the emissivity was set to a value 0.7. The thermal images were corrected based on the emissivity experimentally obtained and used to validate the finite element model simulation for the stamping process. With the validated finite element model, the investigation on the variation in the temperature and stress during each sub-step was performed. With the zero thermal expansion rate, the pure thermal effect on the temperature distribution was simulated. The pure thermal deformation in the Blank (i.e., target surface) was similar to the spring back distance after the blank was released from the molds. During the stamping process, the heat generation was obtained due to either friction between surfaces and plastic deformation of the target surface. We found that the plastic deformation played a critical role in the final temperature rise.

A dual‐scale three‐dimensional thermo‐viscoelastic model for the hot stamping simulation of thermoplastic composites

A three-dimensional viscoelastic analysis of thermoplastic resin matrix composite laminates during hot stamping

Prediction of the Temperature of Large Framed Mold and Curing Deformation of Composite Components in the Autoclave Process

Numerical simulation analysis of forming of continuous fiber reinforced polypropylene composites: Relaxation, creep, and hot stamping

Multi-scale finite element simulation of the thermoforming of a woven fabric glass fiber/polyetherimide thermoplastic composite

A Three-Dimensional Thermal Model for Viscoelastic Polymer Melt Packing Process in Injection Molding

An Improved Analytical Solution For Process-Induced Residual Stresses And Deformations In Flat Composite Laminates Considering Thermo-Viscoelastic Effects

Simulations of Three-Dimensional Thermal Residual Stress and Warpage in Injection Molding

Thermo-mechanical coupled simulation of hot stamping components for process design

Temperature-Dependent modelling of tension, in-Plane shear, and bending behaviour in non-isothermal thermo-Stamping process simulation of unidirectional UHMWPE fibre reinforced thermoplastic TPU composites

A Thermo-Viscoelastic Analytical Model for Residual Stresses and Spring-in Angles of Multilayered Thin-Walled Curved Composite Parts

Three-dimensional Simulations of Non-Isothermal Transient Flow and Flow-Induced Stresses During the Viscoelastic Fluid Filling Process

Numerical simulation for hot diaphragm forming process of thermosetting resin matrix composites

A hybrid lamination model for simulation of woven fabric reinforced thermoplastic composites solid-state thermo-stamping

Thermomechanical-Phase Transformation Simulation of High-Strength Steel in Hot Stamping

Numerical Simulations of Residual Stresses and Warpage in Injection Molding

Numerical modeling of the thermal deformation during stamping process of an automotive body part

A Comprehensive Review Of Characterization And Simulation Methods For Thermo-Stamping Of 2d Woven Fabric Reinforced Thermoplastics

Coupled of Thermal-Mechanical-transformation Numerical Simulation on Hot Stamping with Static Explicit Algorithm

An Analytical Model on Through-Thickness Stresses and Warpage of Composite Laminates Due to Tool–part Interaction

Coupled thermo-mechanical analysis for plastic thermoforming