Abstract:A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution was examined with measurements of the physically formed parts. Specifically, thickness prediction for most locations on the formed parts was accurate within an 11.6% error margin. However, at two points with significant intra-ply shear, the prediction errors increased to around 20%. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45 degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation in part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Two forming analyses were conducted with ramp rates of 25 mm/s and 80 mm/s to match the equipment's operational limits. It was observed that higher forming rates led to a greater likelihood of defects, as evidenced by a 15% and 10% increase in the formed part areas with longer slip paths and higher traction magnitudes, respectively. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

Characterization of Inter-Ply Slipping Behaviors in Hot Diaphragm Preforming: Experiments and Modelling

Inter-Ply Slipping Behaviors and Kinetic Equation of Carbon Fiber-Reinforced Epoxy Prepregs for Hot Diaphragm Preforming

Analysis and Characterization of Interlaminar Tack for Different Prepreg Materials During Automated Fiber Placement

Characterization of Intra‐ply Shear Behaviors of Unidirectional Prepregs During Hot Diaphragm Forming Process

Numerical simulation for hot diaphragm forming process of thermosetting resin matrix composites

Modeling and experimental validation of compaction pressure distribution for automated fiber placement

Characterization of Prepreg-Prepreg and Prepreg-Tool Friction for Unidirectional Carbon Fiber/epoxy Prepreg During Hot Diaphragm Forming Process

Ply-ply Friction Behavior Between Unidirectional Thermoplastic Prepreg Plies During Thermoforming: Characterization and Modeling

Understanding the Impact of Fibre Wrinkle Architectures on Composite Laminates Through Tailored Gaps and Overlaps

Interply friction of carbon fiber/epoxy prepreg stacks under different processing conditions

Compaction Pressure Distribution and Pressure Uniformity of Segmented Rollers for Automated Fiber Placement

Effects of Processing Parameters on the Forming Quality of C-Shaped Thermosetting Composite Laminates in Hot Diaphragm Forming Process

Friction Resistance of Uncured Carbon/Epoxy Prepregs under Thermoforming Process Conditions: Experiments and Modelling

Experimental investigation of friction between prepreg tape and compaction roller for prepreg tape hoop winding

EFFECTS OF TEMPERATURE AND MOLDING RATE IN HOT DIAPHRAGM FORMING PROCESS ON THE FORMING QUALITY OF C-SHAPED COMPOSITE

Development and Verification of a Finite Element Model for Double Diaphragm Preforming of Unidirectional Carbon Fiber Prepreg

Analyses of Wrinkling Mechanisms During Forming of Multi-Layer Woven Fabric Reinforced Thermoplastic Prepregs

Modeling and Optimization of Interlaminar Bond Strength for Composite Tape Winding Process

A Simple Method for the Measurement of Compaction and Corresponding Transverse Permeability of Composite Prepregs

Modeling and analysis of compaction roller deformation for fiber placement

A Modeling Framework for the Thermoforming of Carbon Fiber Reinforced Thermoplastic Composites