Abstract:Additive manufacturing and annealing process of short carbon fiber‐reinforced nylon 6. The mechanical properties of short carbon fiber‐reinforced nylon 6 (CF‐PA6) components formed by fused filament fabrication (FFF) are significantly affected by the process parameters of additive manufacturing and heat treatment. In this study, the effects of printing speed, carbon fiber aspect ratio, and annealing temperature on fiber orientation were investigated by observation of single‐layer‐single‐fiber samples. Furthermore, a two‐stage annealing process was proposed to increase the tensile modulus of CF‐PA6 based on the correlation analysis results between the degree of fiber alignment and the variation of tensile modulus. According to the calculation of the Pearson correlation coefficient, the tensile modulus was highly correlated with the degree of fiber alignment under different printing speeds and fiber aspect ratios. The variation in tensile modulus and fiber orientation was also consistent when the annealing temperature was lower than the crystallization temperature. Conversely, the variation of tensile modulus and fiber orientation were opposite, as the annealing temperature was higher than the crystallization temperature because of the influence of crystallinity. Through increasing the degree of fiber alignment and crystallinity of the parts, the proposed two‐stage annealing method could increase the tensile modulus of the parts to 9.0 GPa, which was 16.81% higher than that of single‐temperature annealing. Highlights The effects of annealing temperature, carbon fiber aspect ratio and printing speed on fiber orientation were illustrated. The relationship between the degree of fiber alignment and the variation of tensile modulus was established. The proposed two‐stage annealing method, considering fiber orientation and crystallinity, significantly increased the tensile modulus of CF270‐PA6 parts from 7.7 to 9.0 GPa. The quantitative analysis of the fiber orientation is realized by the statistical analysis of the plane fiber orientation angle of the single‐layer‐single‐fiber sample.

Enhancing the mechanical strength of Multi Jet Fusion–printed polyamide 12 and its glass fiber-reinforced composite via high-temperature annealing

Influences of isothermal annealing post‐treatment on mechanical performances in fused deposition modeling manufactured short carbon fibrous PETG and PA composites

Additive Manufacturing of Polyamide 66: Effect of Process Parameters on Crystallinity and Mechanical Properties

A detailed evaluation of surface, thermal, and flammable properties of polyamide 12/glass beads composites fabricated by multi jet fusion

Effects of build positions on the thermal history, crystallization, and mechanical properties of polyamide 12 parts printed by Multi Jet Fusion

Two‐stage annealing method for short carbon fiber‐reinforced nylon 6 in fused filament fabrication

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

A Comprehensive Investigation on 3D Printing of Polyamide 11 and Thermoplastic Polyurethane via Multi Jet Fusion

Experimental Characterisation and Finite Element Modelling of Polyamide-12 Fabricated via Multi Jet Fusion

Investigating the Effects of Annealing on the Mechanical Properties of FFF-Printed Thermoplastics

Effects of processing parameters and annealing on the mechanical properties of polyether ether ketone(PEEK) via fused deposition modeling(FDM)

Increasing the Isotropy of 3D Printed Poly(ether ether ketone) Using a Combination of Bimodal Polymer Blends and Post-Process Thermal Annealing

Investigating the influence of annealing and nozzle diameter on tensile strength of polyethylene terephthalate glycol composites

Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting

Influences of heat treatment on mechanical properties of SCF/PEEK composites in FDM‐3D printing process with UV laser assistance

Improvement of Heat Treatment Process on Mechanical Properties of FDM 3D-Printed Short- and Continuous-Fiber-Reinforced PEEK Composites

Infrared on-site heating for material extrusion additive manufacturing of carbon fiber filled polyphenylene sulfide and its nano-graphene-reinforced alternatives

An experimental investigation on the tensile properties of PEEK-PEI sandwich structures prepared via fused filament fabrication

Interlayer enhancement of 3D printed CF/PLA composites via localized microwave welding and annealing-induced crystallization

Comparative study on 3D printing of polyamide 12 by selective laser sintering and multi jet fusion

Selective Laser Sintering vs Multi Jet Fusion: a comprehensive comparison study based on the properties of glass beads reinforced PA12