Abstract:When the lateral dimension of the tool head is close to or greater than a quarter of the longitudinal wave length, the tool head will produce severe lateral vibration. The coupling of the lateral vibration and the longitudinal vibration makes the amplitude distribution of the tool head's radiation surface uneven, which seriously affects the welding quality. To solve the problem of uneven amplitude distribution of the two-dimensional tool head's radiating surface, in the paper we conduct an optimized design study on a two-dimensional ultrasonic plastic welding system. First, using the theory of phononic crystal dislocations, we construct a nearly periodic phononic crystal homogenous dislocation junction on a large-sized long strip tool head, and use the homogenous dislocation junction to change the regular lattice arrangement of the phononic crystal structure to adjust the position of the band gap and increase the width of the band gap, so that the operating frequency of the two-dimensional ultrasonic plastic welding system can be located in the band gap of the lateral vibration of the tool head, and the effective control of the lateral coupling vibration of the tool head can be achieved, thus optimizing the amplitude uniformity of the radiating surface of the tool head and increasing the amplitude gain. Although the homogenous dislocation junction structure improves the amplitude uniformity of the radiating surface of the tool head, the lateral dislocation effect of the homogenous dislocation junction causes the sound waves in the band gap frequency range to propagate along the dislocation channel, while the dislocation line channel is located in the middle of the tool head, which results in a larger displacement of the middle part of the tool head's radiating surface, and a smaller displacement on both sides. Therefore, the further optimizing of the two-dimensional tool head is required. In this study, the nearly periodic phononic crystal inclined groove structure is used to better optimize the amplitude distribution uniformity of the radiating surface, and the influence of the inclined groove structure parameters on the longitudinal resonance frequency and amplitude distribution uniformity of the ultrasonic plastic welding system are analyzed, that is, the inclined groove can better improve the uniformity of the amplitude distribution than the straight groove, but the angle of inclination of neither the inner nor outer inclined grooves should be too large: the optimal range is 3 degrees-6 degrees. In addition, the difference in inclination angle between the inner inclined groove and the outer inclined groove should not be too large, and the angle difference from 0 degrees to 2 degrees is best. The simulation results show that the nearly periodic phononic crystal homogenous dislocation junction and inclined groove structure can optimize the two-dimensional ultrasonic plastic welding system, which provides a basis for further research on the theory of lateral vibration suppression.

Research on Intelligent Optimization Design of Large-scale Three-dimensional Ultrasonic Vibration System

Large-scale Piezoelectric Ultrasonic Transducers with Tubular Near-Period Phononic Crystal Point Defect Structure

Research on Acoustic Control of Coupled Vibration System of Transducers Using Acoustic Surface and Topological Defect Structures

Optimization of a Sandwich Longitudinal Vibration Transducer with a Large Radiation Surface Based on Hole Structure of Near- Periodic Phononic Crystal

Progress and optimization design of high power piezoelectric ceramic ultrasonic vibrating system

Intelligent Optimization Design of a Phononic Crystal Air-Coupled Ultrasound Transducer

Study on a Large-Scale Three-Dimensional Ultrasonic Plastic Welding Vibration System Based on a Quasi-Periodic Phononic Crystal Structure

Optimization Design Method for Ultrasonic Transducers Based on Top Basic Skeleton Method and Sound Pressure Distribution in the Sound Field

Optimization Design of High Frequency Piezoelectric Ultrasonic Transducer for IC Packaging

Performance and Robustness Improvements in Ultrasonic Transportation Against Large-Scale Streaming

Two-Dimensional Ultrasonic Plastic Welding System Based On Phononic Crystal Dislocation Theory

Optimization on Ultrasonic Plastic Welding Systems Based on Two-Dimensional Phononic Crystal.

Structural Optimization Study on a Three-Degree-of-Freedom Piezoelectric Ultrasonic Transducer

Design of Ultrasonic Vibration System in Ultrasonic Vibration Assisted Micro Machining

Large-dimension Piezoelectric Ceramic Composite Transducer with Point-Defect, Square-Lattice Phononic Crystal

Building the Isotropic Acoustic Potential Well with Strong Constraint Boundary to Improve the Stability of Ultrasonic Transportation

Design and simulation of a 2-D array flexible ultrasound transducer system for tissue characterization – A pilot study

Design Optimization of Ultrasonic Transducer for Medical Application Based on an Integrating Method

Suppression of Lateral Vibration in Rectangular Ultrasonic Plastic Soldering Tool Based on Phononic Crystal Structure

Optimal Design of Large-Sized Sandwich Transducer Based on Two-Dimensional Phononic Crystal

Research on Automatic Optimization Design of Ultrasonic Motors