Abstract:It is common on space vehicles to have thermal insulation adhesively bonded to a metal structure. A typical defect in such structures is an interlayer disbond, which may occur either between the insulation and the metal substructure or between the layers of multilayer thermal insulation. One-sided thermal nondestructive testing (TNDT) using surface optical heating, such as Xenon flash or quartz tube, may detect disbonds if the thermal insulation thickness does not exceed a few millimeters and disbonds are not very small. In thicker insulation, the effectiveness of the inspection can be improved by using electrical induction to heat the metal base. In both cases, thermal excitation can be areal heating, which is heat projected over an area by a stationary heat source, or scanned linear heating (SLH), which is a linear heater scanned across the test subject. In the latter, either the linear heater is moved across a stationary test subject, or the linear heater is stationary and the test subject is moved. The SLH method usually provides a higher inspection rate (inspected area unit time). In this research, both the theoretical and experimental features of both optical and induction heating have been investigated and compared in the application to non-metallic insulation adhesively bonded to a metal structure. The effectiveness of using neural networks (NN) for characterizing defects has also been studied to demonstrate that optimal NN training should involve 4–5 points selected in defect areas close to non-defect areas, and the NN input data should be prepared by applying the known technique of Thermographic Signal Reconstruction (TSR). Since SLH provides more uniform heating, it provides higher quality IR thermograms than those obtained from areal (flash) heating and this improves the detectability of defects in thermal insulation to a depth of 4–6 mm. Other advantages of SLH for TNDT testing are (1) an inspection rate that is twice as high as an area heating technique and (2) a better potential for fully automated (robotic) testing.

Detecting Defects in Composites Using Combined Heating/Cooling: Theory and Experiments

Thermal Nondestructive Testing of Composite and Metal Parts Manufactured by Additive Technologies

Design and Testing of a Micro Thermal Sensor for Non-Contact Surface Defect Detection.

The Detection and Characterization of Defects in Metal/Non-metal Sandwich Structures by Thermal NDT, and a Comparison of Areal Heating and Scanned Linear Heating by Optical and Inductive Methods

Design and Testing of a Micro-thermal Sensor Probe for Nondestructive Detection of Defects on a Flat Surface

Distance Effect in Transient Thermography for Internal Defects Detection in Composites

Numerical Modelling of the Heat Source and the Thermal Response of an Additively Manufactured Composite during an Active Thermographic Inspection

Infrared Thermography and Thermal Nondestructive Testing

Thermal Nondestructive Testing: Development of Conventional Directions and New Trends (A Review)

Detection and characterisation of defects in composite materials using microwave non-destructive testing methods

Defect Detection and Depth Estimation in Composite Materials for Pulsed Thermography Images by Nonuniform Heating Correction and Oriented Gradient Information

Thermal non‐destructive testing and evaluation for inspection of carbon fibre‐reinforced polymers

Multiphysics Structured Eddy Current and Thermography Defects Diagnostics System in Moving Mode.

Nondestructive testing of composite T-Joints by TNDT and other methods

Noninvasive Methods of Active Thermographic Investigation: Short Overview of Theoretical Foundations with an Example of Application

Nde of Composites Delamination by Infrared Thermography

Detection and identification of delamination defects in CFRP laminates using nonlinear frequency-modulated infrared thermal wave testing technology

Defect Detection Capabilities of Pulse Compression Based Infrared Non-Destructive Testing and Evaluation

Finite Element Simulation Analysis of Infrared Thermal Wave Detection on Composite Insulators

Efficiency of using different types of infrared imagers in active thermal nondestructive testing of delaminations in non-metals

Exploiting temperature measurements for cure monitoring of FRP composites—Applications with thermocouples and infrared thermography