Abstract:Carbon dioxide (CO2) is injected into reservoirs for enhanced oil recovery worldwide, which is an important technology to reduce carbon emissions from burning and consumption of fossil fuels. However, it is difficult to control the mobility of carbon dioxide in the formation, thus limiting its extensive utilization. In this work, particulate matter (PM) from flue gas was used to obtain an interfacial armored foam for controlling the CO2 mobility in porous media. Both homogeneous and heterogeneous porous model experiments were adopted to study CO2 foam flow behavior in porous media. Furthermore, the viscosity, interfacial viscoelasticity, and microstructure of foam were measured to help understand the mobility control mechanism. The results showed that the interfacial adsorption and compression of PM formed a particle armor on the CO2-liquid interface, which improved foam film roughness and changed the interface to be more solid-like. Consequently, the viscosity of CO2 foams was increased by 2–13 times with the addition of 1.2 wt. % PM. In pore scale, the PM armored foams had stronger Jamin resistance and slipping resistance than bare surfactant foam. Thus, they showed relatively low mobility in porous media. The CO2 gas channel and water breakthrough were inhibited by the injection of 1 PV armored foams. The armored foams showed a higher resistance to the water flushing during the subsequent water flooding. The use of bare PM dispersions did not establish an effective flow resistance in the porous media. However, when a lower CO2 content (20% foam quality) was co-injected with the liquid phase, the improvement of foam resistance factor by adding PM was about 3 times upon addition of PM. Moreover, in the heterogeneous porous model, the mobility of fluids in the high permeability sandpack was effectively controlled by the armored foam, thus increasing the sweeping efficiency in the medium and low permeability sandpacks. Compared with bare surfactant foam flooding, the oil recovery by using armored foam was increased by about 21.3%. After flooding with armored foams, the residual resistance factors of armored foams were reduced to a lower level by enough subsequent water flooding, indicating the temporary plugging and low damage of armored foams in porous media. The significance of this research is the utilization of two important atmospheric pollutants by an inexpensive Pickering foam method for petroleum development and carbon sequestration.This article has not yet been cited by other publications.

Silica aerogel nanoparticle-stabilized flue gas foams for simultaneous CO2 sequestration and enhanced heavy oil recovery

Enhancing foam stability and addressing asphaltene deposition for improved oil recovery in CCUS applications using aerogel nanoparticles

Modified silica nanoparticles stabilized foam for enhanced oil recovery

Hydrophobic in-situ SiO2-TiO2 composite aerogel for heavy oil thermal recovery: Synthesis and high temperature performance

Surfactant and a mixture of surfactant and nanoparticles to stabilize CO2/brine foam, control gas mobility, and enhance oil recovery

Flow Behavior and Displacement Mechanisms of Nanoparticle Stabilized Foam Flooding for Enhanced Heavy Oil Recovery

Experimental investigations of enhanced oil recovery using porous SiO2 aerogel nanosuspensions with emulsifying effects

Aqueous CO 2 Foam Armored by Particulate Matter from Flue Gas for Mobility Control in Porous Media

A Novel Supercritical CO2 Foam System Stabilized With a Mixture of Zwitterionic Surfactant and Silica Nanoparticles for Enhanced Oil Recovery

The foam reinforced with Janus amphiphilic graphene oxide to control steam channeling in heavy oil reservoir

Utilization of nanoparticle-stabilized foam for gas well deliquification

CO2 in water foam stabilized with CO2-dissolved surfactant at high pressure and high temperature

Alumina-extracted residue-derived silica foams with ultra-large pore volume for highly superior post-combustion CO2 capture

Fabrication of elastic SiO2 aerogels with prominent mechanical strength and stability reinforced by SiO2 nanofibers and polyurethane for oil adsorption

Utilization of Surfactant-Stabilized Foam for Enhanced Oil Recovery by Adding Nanoparticles

Nanoparticle and Surfactant Stabilized Carbonated Water Induced In-Situ CO 2 Foam: An Improved Oil Recovery Approach

Enhancing oil–solid and oil–water separation in heavy oil recovery by CO 2 ‐responsive surfactants

Rheological properties and gas channeling plugging ability in CO2 flooding of a hydrophobic nanoparticle-enhanced smart gel system constructed with wormlike micelles

Investigation of the Effect of Nanoparticle-Stabilized Foam on EOR: Nitrogen Foam and Methane Foam

Nanoparticle-reinforced foam system for enhanced oil recovery (EOR): Mechanistic review and perspective

Application of flue‐gas foam in thermal‐chemical flooding for medium‐depth heavy oil reservoirs