Abstract:Double-pipe heat exchangers are devices that provide the transfer of thermal energy between two fluids at different temperatures. The major use of these heat exchangers is the sensible heating or cooling process of fluids where small heat transfer areas are required. The oil cooler is an example of these processes. In this study, fouled finned, clean finned, fouled unfinned, and clean unfinned double-pipe heat exchangers used as an oil cooler in ships have been compared. In thermal design, suggested different Nusselt number equations have been used, and the results of these equations have been shown in tables and figures. As a result, it is evaluated that using fouled finned double-pipe heat exchanger as oil cooler in ships is the most appropriate selection. 1. Introduction A double-pipe heat transfer exchanger consists of one or more pipes placed concentrically inside another pipe of a larger diameter with appropriate fittings to direct the flow from one section to the next. One fluid flows through the inner pipe (tube side), and the other flows through the annular space (annulus). The inner pipe is connected by U-shaped return bends enclosed in a return-bend housing. A typical double-pipe heat transfer exchanger is shown in Fig. 1. Double-pipe heat exchangers can be arranged in various series and parallel arrangements to meet pressure drop. The major use of the double-pipe heat exchanger is the sensible heating or cooling process of fluids where small heat transfer areas (up to 50 m2) are required. This configuration is also very suitable for one or both of the fluids at high pressure because of the smaller diameter of the pipes. The major disadvantage is that they are bulky and expensive per unit of heat transfer surface area. These double-pipe heat exchangers are also called hairpin heat exchangers, and they can be used when one stream is a gas, viscous liquid, or small in volume. These heat exchangers can be used under severe fouling conditions because of the ease of cleaning and maintenance. The outer surface of the inner tube can be finned, and then, the tube can be placed concentrically inside a large pipe, as shown in Fig. 2. In another type, there are multi tubes, finned or bare, inside a larger pipe. The fins increase the heat transfer surface per unit length and reduce the size and, therefore, the number of hairpins required for a given heat duty. Integrally, resistance-welded longitudinal fins have proven to be the most efficient for double-pipe heat exchangers. Fins are most efficient when the film coefficient is low.

Thermal efficiency of environmentally friendly closed cooling systems of marine power plants

Numerical Study on Thermal Performance of a BOG Heat Exchanger in the Inclined Condition

Improving the compact heat exchangers with profiled tubes for marine power plants

EN Energy efficiency improvement for the older reefer vessel by the combined compression-ejector refrigeration machine

Thermal efficiency evaluation for multisection heat exchange equipment in heat power installations

Investigation on thermo-economic performance of shipboard waste heat recovery system integrated with cascade latent thermal energy storage

Exergy efficiency and EEXI analysis of a marine power plant at partial load conditions

Thermo-economic optimization and environmental analysis of a waste heat driven multi-ejector chiller for maritime applications

Thermodynamic analysis and multi-objective optimization of a transcritical CO2 waste heat recovery system for cruise ship application

Improving the efficiency of heat recovery circuits of cogeneration plants with combustion of water-fuel emulsions

ANALYSIS OF THE ENERGY EFFICIENCY OF TECHNICAL SOLUTIONS OF THE HEAT-DRIVEN SHIP EJECTOR REFRIGERATION MACHINE FOR OBTAINING SUB-ZERO TEMPERATURES

Marine temperature and humidity regulation combined system: performance analysis and multi-objective optimization

Enhancing shipboard waste heat management with advanced technologies

Study on the seawater cooled PRHRS of a nuclear propulsion ship with the upper heat exchanger for driving force and the seawater heat exchanger as an ultimate heat sink

Thermodynamic Analysis of a Marine Diesel Engine Waste Heat-Assisted Cogeneration Power Plant Modified with Regeneration Onboard a Ship

Analysis of Efficiency of Thermopressor Application for Internal Combustion Engine

Research of the Aerothermopressor Cooling System of Charge Air of a Marine Internal Combustion Engine Under Variable Climatic Conditions of Operation

Study on Three-Dimensional Numerical Simulation of Shell and Tube Heat Exchanger of the Surface Ship under Marine Conditions

Optimization and 4E analysis of integration of waste heat recovery and exhaust gas recirculation for a marine diesel engine to reduce NOx emissions and improve efficiency

An Ocean Thermal Energy Conversion power plant: Advanced exergy analysis and experimental validation

Thermal Design of Double Pipe Heat Exchanger Used as an Oil Cooler in Ships: A Comparative Case Study