Abstract:One of the promising ways to increase fuel and modern gas turbine energy efficiency is using cyclic air intercooling between the stages of high- and low-pressure compressors. For intercooling, it is possible to use cooling in the surface heat exchanger and the contact method when water is injected into the compressor air path. In the presented research on the cooling contact method, it is proposed to use a thermopressor that implements the thermo-gas-dynamic compression process, i.e., increasing the airflow pressure by evaporation of the injected liquid in the flow, which moves at near-sonic speed. The thermopressor is a multifunctional contact heat exchanger when using this air-cooling method. This provides efficient high-dispersion liquid spraying after isotherming in the high-pressure compressor, increasing the pressure and decreasing the air temperature in front of the high-pressure compressor, reducing the work on compression. Drops of water injected into the air stream in the thermopressor can significantly affect its characteristics. An increase in the amount of water increases the aerodynamic resistance of the droplets in the stream. Hence, the pressure in the flow parts of the thermopressor can significantly decrease. Therefore, the study aims to experimentally determine the optimal amount of water for water injection in the thermopressor while ensuring a positive increase in the total pressure in the thermopressor under conditions of incomplete evaporation. The experimental results of the low-consumption thermopressor (air consumption up to 0.52 kg/s) characteristics with incomplete liquid evaporation in the flowing part are presented. The research found that the relative water amount to ensure incomplete evaporation in the thermopressor flow part is from 4 to 10% (0.0175–0.0487 kg/s), without significant pressure loss due to the resistance of the dispersed flow. The relative increase in airflow pressure is from 1.01 to 1.03 (5–10 kPa). Based on experimental data, empirical equations were obtained for calculating the relative pressure increase in the thermopressor with evaporation chamber diameters of up to 50 mm (relative flow path length is from 3 to 10 and Mach number is from 0.3 to 0.8).

Research of the Aerothermopressor Cooling System of Charge Air of a Marine Internal Combustion Engine Under Variable Climatic Conditions of Operation

Analysis of Efficiency of Thermopressor Application for Internal Combustion Engine

Experimental Investigation on Thermal Performance of Phase Change Materials–metal Foam Composites in Ocean Thermal Engine

Experimental Investigation of the Exhaust Device of Turbocharger for Marine Engines

A numerical study on the effects of charge air temperature on the combustion and emission characteristics of a marine generator engine

Marine temperature and humidity regulation combined system: performance analysis and multi-objective optimization

Investigation of Thermopressor with Incomplete Evaporation for Gas Turbine Intercooling Systems

Study of the functional parameters of main engine turbocharger for a tanker ship

Modeling load effect of marine diesel engines on cooling system operation

Thermal efficiency of environmentally friendly closed cooling systems of marine power plants

Thermo-economic optimization and environmental analysis of a waste heat driven multi-ejector chiller for maritime applications

Methodological Aspects of Assessing the Thermal Load on Diesel Engine Parts for Operation on Alternative Fuel

A novel heat integration development and multi-objective optimization for a marine diesel engine toward a framework of waste-to-electric power, dual-stage coolant, and distilled water

Aerodynamic modification and optimization of intermediate pressure compressor in marine intercooled recuperated gas turbine

THE COMPOSITION OF THE PNEUMATIC SYSTEM FOR LOCAL MULTI-CIRCUIT COOLING ON AUTO TRACTOR DIESEL PARTS JUSTIFICATION

A Novel Approach to Heat Integration Development and Multi-Objective Optimization for a Marine Diesel Engine: Towards a Framework of Waste-to-electric Power, Dual-Stage Coolant, and Distilled Water

Thermodynamic analysis of exhaust heat recovery of marine ice using organic rankine cycle

Thermodynamic Analysis of Hybrid Two-Stage CO 2 Mechanical Compression–ejector Cooling Cycle

ANALYSIS OF THE ENERGY EFFICIENCY OF TECHNICAL SOLUTIONS OF THE HEAT-DRIVEN SHIP EJECTOR REFRIGERATION MACHINE FOR OBTAINING SUB-ZERO TEMPERATURES

Thermodynamic Analysis of a Marine Diesel Engine Waste Heat-Assisted Cogeneration Power Plant Modified with Regeneration Onboard a Ship

Experimental Research of the Excessive Water Injection Effect on Resistances in the Flow Part of a Low-Flow Aerothermopressor