Abstract:Austenitic stainless steels have for some time been used as superheater tubes in the electricity generation industries in harsh environments with temperatures as high as 650°C at pressures of some 200 atm; they are expected to provide reliable service for 30 years or more. Their detailed mechanical properties are dependent on the stability of the microstructure, particularly the formation, dissolution, and coarsening of precipitates. Although the precipitation processes have been studied extensively, there remain important discrepancies. It is known that small changes in the chemical composition or thermomechanical processing can profoundly influence the evolution of the microstructure. This review focuses on precipitation in creep resistant austenitic stainless steels, in particular wrought heat resistant grades containing niobium and titanium additions. Conventional alloys such as 18–8 and 16–10 are included together with the new NF709 (20–25) and other recent variants. Precipitates forming in age hardening austenitic stainless steels are only briefly presented. Many studies have shown that MX is not a stoichiometric phase, and that chromium can be incorporated in the metal sublattice. Furthermore, the reported compositions show considerable variation. These studies are assessed and an explanation is offered, in terms of the Gibbs–Thompson effect, for the variation. A rational consideration of all the results suggests a size dependence in line with capillarity considerations. The MX phase does not form in isolation; its stability also depends on the formation of M23C6. The literature reveals that NbC is more stable than M23C6 but the case for TiC is less certain. The formation of Z phase in nitrogen bearing steels is a further complicating factor, and it is concluded that its formation is not adequately understood. This is unlike the case for M23C6, where there is consistent reporting in the literature. Finally, work on the M6C carbide in austenitic stainless steels is critically assessed. It is found that its detailed composition is not well characterised and that there are no general rules apparent about its formation. The review also covers intermetallic compounds such as σ phase. It is clear that chromium concentrations in excess of 18 wt-%, combined with a low carbon concentration, promote the formation of σ phase. This has implications particularly for steels containing niobium and titanium, both of which getter carbon. Other compounds reviewed include χ and G phases, which form at high temperatures and during very long aging such as that encountered in service.

Sensitization and Self-healing in Austenitic Stainless Steel: Quantitative Prediction Considering Carbide Nucleation and Growth

Evaluation of Sensitization Behaviors on the Heat-Affected Zone of Austenitic Stainless Steel Weld by Thermal Cycles of Actual Multi-pass Welding

A detailed electrochemical analysis of sensitized AISI 410 martensitic stainless steel

The effects of deformation induced martensite on the sensitization of austenitic stainless steels

Intergranular Corrosion Analysis of Austenitic Stainless Steels in Molten Nitrate Salt Using Electrochemical Characterization

The Intergranular Corrosion Susceptibility of Metastable Austenitic Cr–Mn–Ni–N–Cu High-Strength Stainless Steel under Various Heat Treatments

Effects of sensitization induced intercrystalline precipitation on mechanical properties of 204C2 nickel-saving austenitic stainless steel

The Isolated Austenite Forming during High-Temperature Cooling and Its Influence on Pitting Corrosion Resistance in S32750 Duplex Stainless Steel

Electrochemical Analysis on Intergranular Corrosion of Austenitic Stainless Steel Weld in Molten Nitrate Salt

Influence of sensitization on microstructure and passive property of AISI 2205 duplex stainless steel

Understanding the effect of uniaxial tensile strain on the early stages of sensitization in AISI 304 austenitic stainless steel

The Influence of Sensitive Temperature on the Localized Corrosion Resistance of Duplex Stainless Steel Saf2304

Sensitization of 316L Stainless Steel made by Laser Powder Bed Fusion Additive Manufacturing

Effect of strain-induced martensite on hydrogen environment embrittlement of sensitized austenitic stainless steels at low temperatures

Corrosion analysis of post-heat treatment and post-weld SS316 with electrokinetic reactivation and cyclic polarization method

Comparing the Sensitization Behavior and the Corrosion Resistance of the Wrought and Selective Laser Melted 316L Stainless Steels

Precipitation in creep resistant austenitic stainless steels

The behavior of sensitized 309S stainless steel in hydrogen

Intergranular Corrosion Behavior and Mechanism of the Stabilized Ultra-Pure 430LX Ferritic Stainless Steel

Effect of heat treatment on the chromium‐depleted zones of a high carbon martensitic stainless steel

Intergranular Corrosion Sensitivity of Welded Joint of Super304H at High Temperature