Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

About the Use of Concrete Damage Plasticity for Modeling Masonry Post-Elastic Behavior

Finite Element Modelling of Two-way RC Slabs with Varying Modelling Choices

Slip-enhanced plastic-damage constitutive model for masonry structures

A robust computational strategy for failure prediction of masonry structures using an improved multi‐surface damage‐plastic based interface model

Macromechanical Failure Criteria: Elasticity, Plasticity and Numerical Applications for the Non-Linear Masonry Modelling

Calibration of a concrete damage plasticity model used to simulate the material components of unreinforced masonry reinforced concrete infill frames

Simulation of Masonry Wall using Concrete Damage Plasticity Model

Damage Based Constitutive Model for Predicting the Performance Degradation of Concrete

3D hybrid modelling approach combining the finite and discrete element methods: Validation based on masonry shear wall tests

Plastic-Damage Model for Cyclic Loading of Concrete Structures

Calibration of a New Concrete Damage Plasticity Theoretical Model Based on Experimental Parameters

CDPM2: A damage-plasticity approach to modelling the failure of concrete

A damage-plasticity model for the dynamic failure of concrete

A plastic-damage model for concrete

An Orthotropic Elastic-Plastic Constitutive Model for Masonry Walls

Influence of the modelling approach on the seismic assessment of RC structures by nonlinear static analyses

Numerical Analysis of Reinforced Concrete Corbels Using Concrete Damage Plasticity: Sensitivity to Material Parameters and Comparison with Analytical Models

Explicit Approach for the In-Plane Cyclic Behaviors of Unreinforced Masonry Structures Using Finite Particle Method

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

A Damage Model of Concrete including Hysteretic Effect under Cyclic Loading

Comparison of Continuous and Discrete Modeling Strategies for the Structural Assessment of a Masonry Vault Under Dynamic Seismic Loading