Abstract:The development of friction stir welding (FSW) created the basic foundation for friction stir processing (FSP). This process entails refining the local microstructure and achieving the localised plastic deformation due to the stirring effect of the tool, which may involve adding additional filler material as required. The rotating tool involved in the process has a shoulder and pin responsible for heat generation for plastic deformation and localised mixing. The rotating tool is inserted and traversed on the desired surface, tailoring the material properties. The tool's exposure to the surface causes localised plastic deformation and thermal gradient, and microstructural changes occur locally. The present investigation uses Friction Stir Processing (FSP) to fabricate an aluminium metal matrix composite. Recently, the use of aluminium alloy has been replaced by composites because of their increased mechanical and physical properties (specific properties). The experiment leads to manufacturing an aluminium metal matrix composite using aluminium oxide, boron carbide and commercially pure copper dust. Later, the effect of heat treatment on the respective metal matrix composite is studied. A comparative study among three different types of FSP techniques viz. FSP, Reinforced FSP, and Heat-treated Reinforced FSP have been performed. The tool revolution speed (RPM) and tool traverse speed of 400 RPM and 10 mm/min had been implemented, respectively. The T4 Heat-Treatment cycle was used during the current investigation. This investigative study was performed to analyse the changes in grain sizes and hardness values at the stir zone (SZ), thermo-mechanically affected zone (TMAZ), heat affected zone (HAZ) and on the base materials (BM) of the samples. The reinforced FSP metal matrix composite (MMC) showed an 81.26% increase in the micro-hardness value (HV) compared to the base metal. Further on analysing the microstructures, the reinforced FSP composite showed a 65.20% reduction in grain size. Moreover, the Heat-Treated sample showed an increase in the micro-hardness value by 99.8%.

Preliminaries on Hybrid Friction Stir Processing for in-situ Metal Matrix Composite Fabrication

Development and characterization of a novel AA6061 composite reinforced with titanium aluminide via friction stir processing

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Development of Al-Mg2Si Alloy Hybrid Surface Composites by Friction Stir Processing: Mechanical, Wear, and Microstructure Evaluation

Development and Mechanical Assessment of Friction Stir Additive Manufactured Al 6061/TiC/GS Composite

Fabrication of metal matrix composites via friction stir processing

An appraisal of characteristic mechanical properties and microstructure of friction stir welding for Aluminium 6061 alloy – Silicon Carbide (SiCp) metal matrix composite

Investigation on Friction Stir Welding Parameters: Mechanical Properties, Correlations and Corrosion Behaviors of Aluminum/Titanium Dissimilar Welds

Microstructure and Mechanical Properties of Friction Stir Welded SiC/TiB2 Reinforced Aluminum Hybrid Composites

Fabrication of Al6061/Ti 3 AlC 2 MAX phase surface composite by friction stir processing and investigation of wear properties

Microstructure and mechanical characteristics of Al1050/B2O3+Cu hybrid surface nanocomposite fabricated using friction stir processing

Friction welding of titanium alloys: addressing the structural integrity issues through process optimisation

Comparative study of microstructural evolution and mechanical properties in friction stir processed, reinforced friction stir processed, and heat-treated reinforced friction stir processed Al composites

Friction stir welding/processing of metals and alloys: A comprehensive review on microstructural evolution

Integrating interfacial bonding and coordinated deformation in steel/Al bilayers via a pin-less friction stir-assisted synchronous joining-forming approach

Implications of nanomaterials reinforcement along with sub-zero temperature cooling on microstructure and mechanical properties of friction stir processed Al7075 alloy

In-Situ Observation of Fracture Behavior of Ti-Aluminide Multi-Layered Composites Produced by a Hybrid Sintering Process

Effect of nano-Sized Al2O3 Particles on Microstructure and Mechanical Properties of Aluminum Matrix Composite Fabricated by Multipass FSW

Temperature evolution, IMC formation, and resulting bonding efficacy in bimetallic tubular components fabricated by a novel friction stir backward extrusion cladding method

Microstructural characterization and tribological behavior of surface composites fabricated on AA7050-T7451 alloy via friction stir processing

Tailoring of Dissimilar Friction Stir Lap Welding of Aluminum and Titanium