Abstract:The thickness of steel plates used in the member has gradually increased to meet the load-bearing capacity requirements of long-span steel bridges. As the primary connection method of thick steel plate, welding will result in considerable welding residual stress with complex distribution. Large welding residual stress will significantly impact the performance of steel bridges. In this paper, the distribution of residual stress in welded thick steel plate is systematically studied, a specimen with a thickness of 80 mm was designed and fabricated, and the welding residual stress was measured by X-ray diffraction. The finite element model was established and verified by test results. Subsequently, the finite element calculation of the welding residual stress of steel plates with thicknesses of 20, 40, 60, 80, and 100 mm was carried out, and the distribution of surface residual stress and the influence of plate thickness on residual surface stress were studied; then the spatial evolution mechanism of welding residual stress was studied, and the distribution of residual stress inside steel plate and the influence of plate thickness on the distribution of residual stress were revealed. The results show that the surface and internal residual stresses of 20–100 mm thick plates have good symmetry on the paths perpendicular to the weld seam, and asymmetry only occurs in the weld seam and heat-affected zone where the stress fluctuates. On the paths perpendicular to the weld seam, the stress in the X direction transitions from the "M" shape distribution on the surface to the "Π" shape distribution inside for 20–40 mm thick plates, and the residual stress near the weld seam gradually changes from compressive to tensile; The distribution of stress in the X direction in the 80–100 mm thick plate has experienced the transition from "M" shape to "Π" shape to "M" shape, and the stress near the weld seam has experienced the transition from compressive to tensile to compressive. The stress change in the X direction of the 60 mm thick plate is between the above two cases. On the path of internal stress along the thickness, the maximum stress in the X direction is 310–400 MPa for 20–40 mm thick plates, which appears at about 1/2 plate thickness. The maximum stress in the X direction for 60–100 mm thick plates is 400–480 MPa, which appears at 0.2–0.3 times the thickness of the plate from the upper surface. The results could serve as a reference for welding residual stress analysis and guide optimization design of steel bridges made of thick steel plate.

Prediction of transverse welding residual stress considering transverse and bending constraints in butt welding

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

The prediction of residual stress of welding process based on Deep Neural Network

Simulating Welding Residual Stress and Deformation in a Multi-Pass Butt-Welded Joint Considering Balance Between Computing Time and Prediction Accuracy

Influence of Material Model on Prediction Accuracy of Welding Residual Stress in an Austenitic Stainless Steel Multi-pass Butt-Welded Joint

Prediction of welding distortion and residual stress in a thin plate butt-welded joint

Prediction of residual stresses in welded structures based on neural network: a review

Numerical simulation of residual stress of butt-welded joint involved in complex column-beam welded structure

Finite element analysis, prediction, and optimization of residual stresses in multi-pass arc welding with experimental evaluation

Experimental Research of Welding Residual Stress of Butt Welded Joint of Thick Steel Plate

Estimation of Residual Stress in Dissimilar Metals Welding using Deep Fuzzy Neural Networks with Rule-Dropout

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Accurate evaluation on residual stress considering solid-state phase transformation and initial stress in thick weld

Experimental research and numerical analysis of welding residual stress of butt welded joint of thick steel plate

Theoretical Crack Growth Prediction Model for Thick Plate Butt Welding Joints Based on Stress/strain Transitions

Prediction of welding residual stress and deformation in electro-gas welding using artificial neural network

Investigation of Residual Stress in Butt-Welded Plates Considering Phase Transformation

Prediction of Welding Deformation of Complex Thin Wall Structure of 1 500 MPa Grade Ultra-High Strength Steel

Three-dimensional finite element analysis on welding residual stresses of construction steel

Numerical Simulation of Welding for Residual Stress Prediction of Low Carbon Steel

Numerical Study on Welding Residual Stress Distribution of Corrugated Steel Webs