Abstract:The flow behaviour of AA2060 Al alloy under warm/hot deformation conditions is complicated because of its dependency on strain rates (ε˙), strain (ε), and deformation modes. Thus, it is crucial to reveal and predict the flow behaviours of this alloy at a wide range of temperatures (T) and ε˙ using different constitutive models. Firstly, the isothermal tensile tests were carried out via a Gleeble-3800 thermomechanical simulator at a T range of 100, 200, 300, 400, and 500 °C and ε˙ range of 0.01, 0.1, 1, and 10 s-1 to reveal the warm/hot flow behaviours of AA2060 alloy sheet. Consequently, three phenomenological-based constitutive models (L-MJC, S1-MJC, S2-MJC) and a modified Zerilli-Armstrong (MZA) model representing physically based constitutive models were developed to precisely predict the flow behaviour of AA2060 alloy sheet under a wide range of T and ε˙. The predictability of the developed constitutive models was assessed and compared using various statistical parameters, including the correlation coefficient (R), average absolute relative error (AARE), and root mean square error (RMSE). By comparing the results determined from these models and those obtained from experimentations, and confirmed by R, AARE, and RMSE values, it is concluded that the predicted stresses determined from the S2-MJC model align closely with the experimental stresses, demonstrating a remarkable fit compared to the S1-MJC, L-MJC, and MZA models. This is because of the linking impact between softening, the strain rate, and strain hardening in the S2-MJC model. It is widely known that the dislocation process is affected by softening and strain rates. This is attributed to the interactions that occurred between ε and ε˙ from one side and between ε, ε˙, and T from the other side using an extensive set of constants correlating the constitutive components of dynamic recovery and softening mechanisms.

A modified Johnson–Cook model for 2A12 aluminum alloys

A modified Johnson-Cook model considering strain softening of A356 alloy

Study on constitutive relationship of 6061 aluminum alloy based on Johnson-Cook model

A Modified Johnson–Cook Model for Modeling AA6061-T6 under Different Temperatures Considering Ductile Fracture

An Enhanced Johnson–Cook Model for Hot Compressed A356 Aluminum Alloy

A Modified Johnson–Cook Model and Microstructure Evolution of As-Extruded AA 2055 Alloy during Isothermal Compression

Research on Johnson–Cook Constitutive Model of γ-TiAl Alloy with Improved Parameters

Mechanical properties and JC constitutive modification of tungsten alloys under high strain rates and high/low temperatures

Research on High-Temperature Constitutive Relationship of Aluminum Alloy

Analysis of the High Temperature Plastic Deformation Characteristics of 18CrNi4A Steel and Establishment of a Modified Johnson–Cook Constitutive Model

Modification of strain rate strengthening coefficient for Johnson-Cook constitutive model of Ti6Al4V alloy

Modification of the Johnson-Cook relationship for AZ31 magnesium alloy at high strain rates

Application of Four Different Models for Predicting the High-Temperature Flow Behavior of 1420 Al–Li Alloy

Identification of Multiple Parameters of the Bammann–Chiesa–Johnson Constitutive Model with Comprehensive Experiments for Pure Aluminum

Study on Mechanical Properties and Constitutive Model of 5052 Aluminium Alloy

The Comparation of Arrhenius-Type and Modified Johnson–Cook Constitutive Models at Elevated Temperature for Annealed TA31 Titanium Alloy

Modelling the Flow Behaviour of Al Alloy Sheets at Elevated Temperatures Using a Modified Zerilli-Armstrong Model and Phenomenological-Based Constitutive Models

A Modified Johnson–Cook Constitutive Model and Its Application to High Speed Machining of 7050-T7451 Aluminum Alloy

Dynamic Mechanical Properties and Modified Material Constitutive Model for Hot Forged Ti2AlNb over Wide Ranges of Temperature and Strain Rate

Tensile properties and a modified s-Johnson-Cook model for constitutive relationship of AA7075 sheets at cryogenic temperatures

Constitutive Modeling of High-Temperature Flow Behavior of Al-0.62Mg-0.73Si Aluminum Alloy