Abstract:Laser metal-wire deposition (LMwD) exhibits a larger molten pool and layer height during printing, compared to powder bed fusion additive manufacturing; in the present study, these features revealed a more inhomogeneous but easily observable microstructure. The coaxial double laser used herein makes the energy distribution of the molten pool more complex than that afforded by a single laser source, and the microstructure of the LMwD parts was more heterogeneous as well. We observed the microstructure of Ti6Al4V by the double LMwD as-built samples by conducting a laboratory experiment and a simulation. The precipitated martensite (α') phase was defined after eliminating the influence of the β element in an X-ray diffraction analysis, which has not been discussed previously in the literature. We also propose a theory regarding the formation of heat-affected zone (HAZ) bands in an environment that includes the α' phase. Our experiments revealed only white HAZ bands, which can be attributed to the solute partitioning caused by sequential thermal cycling and the absence of the β element. The microhardness of the HAZ band areas was lower than that of both the upper and lower sides. The simulation results indicate that the maximum temperature of 2925 °C restrains the generating of HAZ bands in the final two deposited layers, due to its great difference from the β transus temperature. Moreover, the higher heat accumulation in the upper layers promoted the migration of β-grain boundaries, which may explain why the coarse columnar β grains tended to grow at the edge area in the layers deposited later. We also observed that with the use of high temperature, the nucleation of β grains is more easily promoted in the lower layers. We conclude that the concentration of residual stress in the fusion zone and the first layer is favorable to the nucleation of equiaxed grains.

"Multi-Laser Powder Bed Fusion of Ti6Al4V: Diode Area Melting Utilizing Low-Power 450 nm Diode Lasers"

Dual-laser powder bed fusion using 450 nm diode area melting and 1064 nm galvo-scanning fiber laser sources

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

High power laser powder bed fusion of Ti6Al4V alloy: The control of defects, microstructure, and mechanical properties

Area melting with multi-laser arrays to increase build rate for metal powder bed fusion additive manufacturing

Real-time monitoring of laser powder bed fusion process using high-speed X-ray imaging and diffraction

Investigation of the Microstructure of Ti6Al4V Alloy by Coaxial Double Laser Metal-Wire Deposition

Evolution of Melt Pool and Porosity During Laser Powder Bed Fusion of Ti6Al4V Alloy: Numerical Modelling and Experimental Validation

Stability of molten pool and microstructure evolution of Ti-6Al-4V during laser powder bed fusion with a flat-top beam

Multi-laser Powder Bed Fusion of Ti–6Al–4V Alloy: Defect, Microstructure, and Mechanical Property of Overlap Region

Microstructure Tailoring for High Strength Ti-6Al-4V without Alloying Elements through Optimized Preheating and Post-Heating Laser Scanning in Laser Powder Bed Fusion

Multiphysics Modelling of Laser Powder Bed Fusion Based Additive Manufacturing of Single-Track Build of Ti6Al4V Alloy

Numerical simulation of melt pool size and flow evolution for laser powder bed fusion of powder grade Ti6Al4V

Micro laser powder bed fusion of NiTi alloys with superior mechanical property and shape recovery function

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Processing-microstructure relationships in ferrous alloys via mixed powder laser powder bed fusion

Optimization of Laser Based-Powder Bed Fusion Parameters for Controlled Porosity in Titanium Alloy Components

Unveiling the impact of layerwise laser preheating on microstructure and mechanical response in laser powder bed fusion

In Situ Microstructure Modification Using a Layerwise Surface-Preheating Laser Scan of Ti-6Al-4V during Laser Powder Bed Fusion

Particle-scale computational fluid dynamics study on surface morphology of GH4169 superalloy during multi-laser powder bed fusion with low energy density

Innovative Fabrication Design for In Situ Martensite Decomposition and Enhanced Mechanical Properties in Laser Powder Bed Fused Ti6Al4V Alloy