Abstract:Multi-pass TIG welding was conducted on plates (15×300×180 mm<sup>3</sup>) of aluminum alloy Al-5083 that usually serves as the component material in structural applications such as cryogenics and chemical processing industries. Porosity formation and solidification cracking are the most common defects when TIG welding Al-5083 alloy, which is sensitive to the welding heat input. In the experiment, the heat input was varied from 0.89 kJ/mm to 5 kJ/mm designed by the combination of welding torch travel speed and welding current. Tensile, micro-Vicker hardness and Charpy impact tests were executed to witness the impetus response of heat input on the mechanical properties of the joints. Radiographic inspection was performed to assess the joint's quality and welding defects. The results show that all the specimens displayed inferior mechanical properties as compared to the base alloy. It was established that porosity was progressively abridged by the increase of heat input. The results also clinched that the use of medium heat input (1 to 2 kJ/mm) offered the best mechanical properties by eradicating welding defects, in which only about 18.26 % of strength was lost. The yield strength of all the welded specimens remained unaffected indicated no influence of heat input. Partially melted zone (PMZ) width also affected by heat input, which became widened with the increase of heat input. The grain size of PMZ was found to be coarser than the respective grain size in the fusion zone. Charpy impact testing revealed that the absorbed energy by low heat input specimen (welded at high speed) was greater than that of high heat input (welded at low speed) because of low porosity and the formation of equiaxed grains which induce better impact toughness. Cryogenic (-196 °C) impact testing was also performed and the results corroborate that impact properties under the cryogenic environment revealed no appreciable change after welding at designated heat input. Finally, Macro and micro fractured surfaces of tensile and impact specimens were analyzed using Stereo and Scanning Electron Microscopy (SEM), which have supported the experimental findings.

Nondestructive Testing of an Aluminum Alloy Welded Joint Based on a Mathematical Model of the Thermal Welding Process and Computer Microtomography

Thermal, metallurgical and mechanical analysis of circumferentially multi-pass welded P92 steel pipes

In situ Passive Infrared Thermography Application for the Assessment of Localized Mechanical Properties of Tungsten Inert Gas-Welded Inconel 625 Alloys

Combined Calorimetry, Thermo-Mechanical Analysis and Tensile Test on Welded EN AW-6082 Joints

Tensile failure analysis of laser stake-welded T-joints: X-ray tomography based conformal finite element and fractal theoretical approaches

Numerical Simulation of the Stress-Strain State of a PAW-MIG-Welded 1561 Aluminum Alloy Butt Joint Produced Under Different Process Modes

X-ray Microscopic and Thermodynamic Model Assessments of Softening in TIG-Welded AA 6061-T651

Tensile Behaviors and Mechanical Property Analyses of T-Welded Joint for Thin-Walled Parts in Consideration of Different TIG Welding Currents Using Multiple Damage Models and Fracture Criterions: Numerical Simulation and Experiment Validation

Non-destructive Testing of Quality of Welded Joints of Titanium Plates of Superminiature Eddy-Current Probes

Real Time Non-Destructive Testing Methods of Welding

Quantifying structure-property relationships during resistance spot welding of an aluminum 6061-T6 joint

An experimental methodology to characterize load-based fracture models of third generation advanced high strength steel resistance spot welds

Experimental and numerical study on the tensile ductility of an aluminium alloy with heat-affected zones

Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Ultrasound-assisted material characterization: An innovative method for the non-destructive in-situ detection of microstructural changes of high-strength aluminum alloys

Ultrasonic and structural characterization of anisotropic austenitic stainless steel welds: Towards a higher reliability in ultrasonic non-destructive testing

Numerical Simulation and Experimental Validation of MIG Welding of T-Joints of Thin Aluminum Plates for Top Class Vehicles

A Numerical Simulation Method Considering Solid Phase Transformation and the Experimental Verification of Ti6Al4V Titanium Alloy Sheet Welding Processes

Comparative Study of 5A06 Aluminum Alloy Welded Joints Obtained by Different Laser–Tungsten Inert Gas Hybrid Welding

Impact of ultrasonic vibration power and tool pin profile on mechanical and microstructural behaviour of friction stir welded dissimilar aluminium alloy joints

Experimental and numerical investigation on temperature field and joint tensile failure for CF/PPS-Al alloy interlocking induction welding