Abstract:Vegetable tannins are excellent options to produce adhesives for the panel industry since they have the capacity to reduce formaldehyde emissions and are derived from renewable sources. They also allow for the possibility of increasing the resistance of the glue line through the use of natural reinforcements such as cellulose nanofibrils. Condensed tannins, polyphenols isolated from tree bark, are widely studied for the production of natural adhesives as an alternative to commercial synthetic adhesives. So, the purpose of our research is to show a natural adhesive alternative for wood bonding. Therefore, the objective of the study was to evaluate the quality of tannin adhesives of different species reinforced with different nanofibrils and thus predict which adhesive is the most promising at different concentrations of reinforcement and with different types of polyphenols. To meet this objective, polyphenols were extracted from the bark, nanofibrils were obtained, and both processes followed the current standards. Then, the adhesives were produced, their properties were characterized, and they were chemically analyzed via Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). A mechanical shear analysis of the glue line was also performed. According to the results, the addition of cellulose nanofibrils affected the physical properties of the adhesives, mostly the content of solids and the gel time. In the FTIR spectra, the OH band of the 5% Pinus and 5% Eucalyptus (EUC) TEMPO in the barbatimao adhesive and the 5% EUC of the cumate red adhesive were reduced, possibly due to their higher moisture resistance. Mechanical tests of the glue line showed that barbatimao with 5% Pinus and cumate red with 5% EUC performed best in the dry and wet shear tests. The control was the best-performing sample in the test of the commercial adhesives. The cellulose nanofibrils used as reinforcement did not change the thermal resistance of the adhesives. Therefore, the addition of cellulose nanofibrils to these tannins is an interesting means of increasing the mechanical strength, as occurred in commercial adhesive with 5% EUC. Thus, the physical and mechanical properties of tannin adhesives were better with reinforcement, making it possible to expand the use of these adhesives in the panel industry. At the industrial level, it is important to replace synthetic products with natural ones. Besides environmental and health issues, there is the question of the value of petroleum-based products, which have been widely studied so that they can be replaced.

Effect of replacing Bis-GMA with a biobased trimethacrylate on the physicochemical and mechanical properties of experimental resin composites

Wood Flour-Reinforced Green Composites: Parameter Optimization via Multi-criteria Decision-Making Methods

Effects on dentin nanomechanical properties, cell viability and dentin wettability of a novel plant-derived biomodification monomer

Physicochemical properties of flowable composites using isobornyl methacrylate as diluent monomer

Methacrylic monomer derived from cardanol incorporated in dental adhesive as a polymerizable collagen crosslinker

A novel low shrinkage dimethacrylate monomer as an alternative to BisGMA for adhesive and resin-based composite applications

Marginal integrity and physicomechanical properties of a thermoviscous and regular bulk-fill resin composites

Evaluation of Novel Plant-derived Monomers-based Pretreatment on Bonding to Sound and Caries-affected Dentin

Acrylamides and methacrylamides as alternative monomers for dental adhesives

Mechanical Properties, DMA and Structural Analysis of Cassia Auriculata/PLA Blended Hybrid bio Matrix Composite

Effect of Stearyl Methacrylate Comonomer on the Mechanical and Physical Properties of Dimethacrylate-Based Dental Resins

Substitution of urea-formaldehyde by renewable phenolic compound for environmentally appropriate production of particleboards

Influence of matrix composition on polymerization stress development of experimental composites

Toward replacement of methyl methacrylate by sustainable bio-based isobornyl methacrylate in latex pressure sensitive adhesive

Effect of organoclay and corn straw on the properties of poly (butylene adipate-co-terephthalate) (PBAT) hybrid composites

Surface, mechanical and chemical properties of modified denture resin using natural biopolymer

Improving the tensile properties of hemicellulose/polylactic acid (PLA) blends prepared by solvent casting

Bis-EMA/Bis-GMA ratio effects on resin-properties and impregnated fiber-bundles

Application of Biobased Monomers in Two-Component Methacrylate Resins Using Reaction Monitoring and Design-of-Experiment Analysis

The effect of the vanillin‐derived Si‐containing compound on the curing behavior, thermal and mechanical properties of bismaleimide resins

Substitution of petrochemical compounds for polyphenols of natural origin reinforced with cellulose nanofibrils to formulate adhesives for wood bonding