Abstract:Vegetable tannins are excellent options to produce adhesives for the panel industry since they have the capacity to reduce formaldehyde emissions and are derived from renewable sources. They also allow for the possibility of increasing the resistance of the glue line through the use of natural reinforcements such as cellulose nanofibrils. Condensed tannins, polyphenols isolated from tree bark, are widely studied for the production of natural adhesives as an alternative to commercial synthetic adhesives. So, the purpose of our research is to show a natural adhesive alternative for wood bonding. Therefore, the objective of the study was to evaluate the quality of tannin adhesives of different species reinforced with different nanofibrils and thus predict which adhesive is the most promising at different concentrations of reinforcement and with different types of polyphenols. To meet this objective, polyphenols were extracted from the bark, nanofibrils were obtained, and both processes followed the current standards. Then, the adhesives were produced, their properties were characterized, and they were chemically analyzed via Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). A mechanical shear analysis of the glue line was also performed. According to the results, the addition of cellulose nanofibrils affected the physical properties of the adhesives, mostly the content of solids and the gel time. In the FTIR spectra, the OH band of the 5% Pinus and 5% Eucalyptus (EUC) TEMPO in the barbatimao adhesive and the 5% EUC of the cumate red adhesive were reduced, possibly due to their higher moisture resistance. Mechanical tests of the glue line showed that barbatimao with 5% Pinus and cumate red with 5% EUC performed best in the dry and wet shear tests. The control was the best-performing sample in the test of the commercial adhesives. The cellulose nanofibrils used as reinforcement did not change the thermal resistance of the adhesives. Therefore, the addition of cellulose nanofibrils to these tannins is an interesting means of increasing the mechanical strength, as occurred in commercial adhesive with 5% EUC. Thus, the physical and mechanical properties of tannin adhesives were better with reinforcement, making it possible to expand the use of these adhesives in the panel industry. At the industrial level, it is important to replace synthetic products with natural ones. Besides environmental and health issues, there is the question of the value of petroleum-based products, which have been widely studied so that they can be replaced.

Substitution of urea-formaldehyde by renewable phenolic compound for environmentally appropriate production of particleboards

Cardanol-based adhesive with reduced formaldehyde emission to produce particleboards with waste from bean crops

Influence of Pressing Temperatures on Physical–Mechanical Properties of Wood Particleboards Made with Urea-Formaldehyde Adhesive Containing Al2O3 and CuO Nanoparticles

Lignosulfonate and glycidyl ether modified urea formaldehyde wood adhesives for interior particleboard production

Volatile organic compound (VOC) emissions from no-added-formaldehyde lignosulphonate/pMDI particleboards and their effect on indoor air quality

PHYSICAL AND MECHANICAL PROPERTIES OF PARTICLEBOARD FROM Eucalyptus grandis PRODUCED BY UREA FORMALDEHYDE RESIN WITH SiO2 NANOPARTICLES

Partial replacement of urea-formaldehyde adhesive with fungal biomass and soy flour in plywood fabrication

Exploring Fully Biobased Adhesives: Sustainable Kraft Lignin and 5-HMF Adhesive for Particleboards

Ureido Hyperbranched Polymer Modified Urea-Formaldehyde Resin as High-Performance Particleboard Adhesive

Investigation into a bio-based adhesive in combination with fire retardants for particleboard manufacture

Effect of tannin and calcium lignosulfonate-based adhesives on particleboards production

Performance of eucalypt particleboard with the addition of farm waste

Engineering the Properties of Eco-Friendly Medium Density Fibreboards Bonded with Lignosulfonate Adhesive

Eco-Friendly Adhesives Based on the Oligomeric Condensed Tannins-Rich Extract from Alder Bark for Particleboard and Plywood Production

The effect of urea-formaldehyde adhesive modification with diisocyanate-functionalized nanocellulose on the properties of particleboard

Easy Preparation, High Water Resistance Glucose-Based Environment-Friendly Wood Adhesives

Adhesion properties and formaldehyde emissions of MnO2/UF nanocomposite adhesives

Valorization of Uruguayan Pinus elliottii Bark by Developing Sustainable Adhesives

Properties of patula pine plywood using phenolic resin-impregnated veneers

Substitution of petrochemical compounds for polyphenols of natural origin reinforced with cellulose nanofibrils to formulate adhesives for wood bonding

Eco-Friendly Phenol-Urea-Formaldehyde Co-condensed Resin Adhesives Accelerated by Resorcinol for Plywood Manufacturing