Abstract:Developing formaldehyde-free and excellent water resistance has constantly been at the center of attention of wood adhesives. In addition to enhancing the adhesive itself, the modification of wood interface can also improve its bonding strength and water resistance. In this study, aqueous solutions of NaIO 4 and NaClO 2 have been sprayed onto the surface of poplar veneer evenly. An activated wood interface equipped with -CHO and -COOH was prepared. Traditional polyurethane adhesives are primarily two-component, with excessive manufacturing cost, complicated production and use procedures. In this study, a single component high branched polyurethane adhesive (GI) was synthesized via a A 2 +B 3 oligomerization method by using glycerol and isophorone diisocyanate (IPDI). Using branched polyamine (PA 4 N ) as a modifier, GI was modified to GI-PA 4 N , which was used as an adhesive and then hot pressed with the activated wood to make three-layer plywood. The bonding interface was equipped with urethane bonds, urea-based chemical bonds, amide bonds, Schiff bonds and hydrogen bond, which considerably enhanced the stability and water resistance of the bonding interface. FT-IR and XPS confirmed the existence of -CHO and -COOH at the interface of the activated wood, and characterized the synthesis mechanism and bonding mechanism of GI-PA 4 N . The results indicated that when the mass ratio of polyurethane to polyamine was 4:1, the overall performance of the adhesive was the best. The dry bonding strength increased from 1.92 MPa to 3.63 MPa, and the wet bonding strength increased from 1.77 MPa to 3.13 MPa, much higher than the minimum requirement of GB/T 17657–2013 (0.7 MPa). A formaldehyde-free, high-performance plywood with excellent water resistance was successfully prepared using wood interfacial activation and branched polyamine modification.

Eco-Friendly Phenol-Urea-Formaldehyde Co-condensed Resin Adhesives Accelerated by Resorcinol for Plywood Manufacturing

Easy Preparation, High Water Resistance Glucose-Based Environment-Friendly Wood Adhesives

Preparation of Environmentally Friendly Urea-Hexanediamine-Glyoxal (HUG) Resin Wood Adhesive

Influence of Single/Collective Use of Curing Agents on the Curing Behavior and Bond Strength of Soy Protein-Melamine-Urea-Formaldehyde (SMUF) Resin for Plywood Assembly

Study on structure and properties of glyoxal-urea-formaldehyde copolycondensation resin

Synthesis and Characterization of an Environmentally Friendly Phenol–Formaldehyde Resin Modified with Waste Plant Protein

Preparation and characterization of a novel environment-friendly urea-glyoxal resin of improved bonding performance

Modification of urea-formaldehyde resin adhesives with oxidized starch using blocked pMDI for plywood

Partial replacement of urea-formaldehyde adhesive with fungal biomass and soy flour in plywood fabrication

Modified phenol formaldehyde resin with sodium silicate as a low-cure wood adhesive

The Removal of Formaldehyde from Urea Formaldehyde Adhesive by Sodium Borohydride Treatment and Its Application in Plywood

Ureido Hyperbranched Polymer Modified Urea-Formaldehyde Resin as High-Performance Particleboard Adhesive

An Eco-Friendly Wood Adhesive Consisting of Soybean Protein and Cardanol-Based Epoxy for Wood Based Composites

Synthesis and Characterization of Sucrose and Ammonium Dihydrogen Phosphate (SADP) Adhesive for Plywood

Development and Characterization of Bio-Based Formaldehyde Free Sucrose-Based Adhesive for Fabrication of Plywood

Investigation of Novel Thermosetting Copolymer-Based Monomethylolurea-Glyoxal for Wood Manufacturing

OPTIMIZATION OF MATERIAL COMPOSITION FOR THE SYNTHESIS OF UREA FORMALDEHYDE (UF) RESIN MODIFIED BY POLYVINYL ALCOHOL (PVA)

Bonding properties of polyurethan enhanced by branched polyamine and wood interfacial activation

Preparation of Organic-Inorganic Phosphorus-Nitrogen-Based Flame Retardants and Their Application to Plywood

Comparison of the properties of phenolic resin synthesized from different aldehydes and evaluation of the release and health risks of VOCs

Plywood for Construction Purposes on a Phenol-Formaldehyde Binder Modified with Hydrogen Peroxide