Abstract:A ferroelectric polyvinylidene fluoride (PVDF)‐based composite film (PVDF‐MXene) with high β‐phase content is prepared as the protective layer on zinc metal by the 3D printing method. Such a protective layer can manipulate the concentration distribution of zinc ions and enable the uniform zinc growth, which effectively enhances the performance of zinc batteries. Zinc (Zn) metal anodes of aqueous zinc‐ion batteries (AZIBs) have attracted significant attention due to their high theoretical capacities, low redox potentials, and low cost. However, uncontrollable dendrite formation and side reactions can result in limited reversible cycling and quick failure of the batteries. Herein, a polyvinylidene fluoride (PVDF)‐based protection layer (PVDF‐MXene) with high β‐phase content is built by the 3D printing method. The synergistic effect attributed to the 3D printing approach and MXene nanosheets contributes to phase transition of the PVDF polymer chains from α‐phase to β‐phase, improving the ferroelectric properties of the printed PVDF films. Such a protection layer can manipulate the concentration distribution of zinc ions and enable the uniform growth of zinc plates. As a result, symmetrical zinc batteries using such anodes (PVDF‐MXene‐Zn) exhibit reversible Zn plating/stripping with low voltage hysteresis at 1.0 mA cm−2, 1.0 mAh cm−2 for over 4200 h, and a high‐rate capability up to 10 mA cm−2. When assembled with MnO2 and activated carbon, the resulting Zn‐MnO2 battery and zinc‐ion capacitor exhibited significantly enhanced cycling stability. The proposed strategy in this study provides a novel strategy for the protection of the zinc anode, thus promoting the practical application of ZIBs.

3D Cold‐Trap Environment Printing for Long‐Cycle Aqueous Zn‐Ion Batteries

A Homogeneous Plating/stripping Mode with Fine Grains for Highly Reversible Zn Anodes

3D Cold‐Trap Environment Printing for Long‐Cycle Aqueous Zn‐Ion Batteries (Adv. Mater. 9/2023)

MICROFLUIDIC‐assisted 3d Printing Zinc Powder Anode with 2d Conductive MOF/MXene Heterostructures for High‐stable Zinc‐organic Battery

Assembly of Metal–Organic Chemical Conversion Layers As Ion Sieves along with Exposing Zn(002) Planes for Stable Zn Metal Anode

3D Porous Copper Skeleton Supported Zinc Anode toward High Capacity and Long Cycle Life Zinc Ion Batteries

Ultra‐Stable 3D‐Printed Zn Powder‐Based Anode Coated with a Conformal Ion‐Conductive Layer

3D Printing of MXene‐Enhanced Ferroelectric Polymer for Ultrastable Zinc Anodes

Establishing Thermal Infusion Method for Stable Zinc Metal Anodes in Aqueous Zinc‐Ion Batteries

Long lifespan and high-rate Zn anode boosted by 3D porous structure and conducting network

Multifunctional anchoring effect enables ultra-stable 3D-printed zinc powder-based anode

In‐situ Implanting 3D Carbon Network Reinforced Zinc Composite by Powder Metallurgy for Highly Reversible Zn‐based Battery Anodes

3D‐Printed Multi‐Channel Metal Lattices Enabling Localized Electric‐Field Redistribution for Dendrite‐Free Aqueous Zn Ion Batteries

Encapsulation of Metallic Zn in a Hybrid MXene/Graphene Aerogel as a Stable Zn Anode for Foldable Zn‐Ion Batteries

3D zincophilic micro-scaffold enables stable Zn deposition

Dual Porous 3D Zinc Anodes toward Dendrite-Free and Long Cycle Life Zinc-Ion Batteries

Preparation of Nano-copper Modified Three-dimensional Zinc Mesh Electrode and Its Performance as Anode for Zinc-ion Batteries

Sn Penetrated Zincophilic Interface Design in Porous Zn Substrate for High Performance Zn‐Ion Battery

Spatially Restricted Deposition of Zn Metal in Localized-Activation 3D Electrode Enables Long-Term Stable Zinc Ion Batteries

3D Printing‐Induced Phase Transition in Ferroelectric Porous Polymer Coatings for Stable Zinc Anodes

High Zinc Utilization Aqueous Zinc Ion Batteries Enabled by 3D Printed Graphene Arrays