Abstract:A ferroelectric polyvinylidene fluoride (PVDF)‐based composite film (PVDF‐MXene) with high β‐phase content is prepared as the protective layer on zinc metal by the 3D printing method. Such a protective layer can manipulate the concentration distribution of zinc ions and enable the uniform zinc growth, which effectively enhances the performance of zinc batteries. Zinc (Zn) metal anodes of aqueous zinc‐ion batteries (AZIBs) have attracted significant attention due to their high theoretical capacities, low redox potentials, and low cost. However, uncontrollable dendrite formation and side reactions can result in limited reversible cycling and quick failure of the batteries. Herein, a polyvinylidene fluoride (PVDF)‐based protection layer (PVDF‐MXene) with high β‐phase content is built by the 3D printing method. The synergistic effect attributed to the 3D printing approach and MXene nanosheets contributes to phase transition of the PVDF polymer chains from α‐phase to β‐phase, improving the ferroelectric properties of the printed PVDF films. Such a protection layer can manipulate the concentration distribution of zinc ions and enable the uniform growth of zinc plates. As a result, symmetrical zinc batteries using such anodes (PVDF‐MXene‐Zn) exhibit reversible Zn plating/stripping with low voltage hysteresis at 1.0 mA cm−2, 1.0 mAh cm−2 for over 4200 h, and a high‐rate capability up to 10 mA cm−2. When assembled with MnO2 and activated carbon, the resulting Zn‐MnO2 battery and zinc‐ion capacitor exhibited significantly enhanced cycling stability. The proposed strategy in this study provides a novel strategy for the protection of the zinc anode, thus promoting the practical application of ZIBs.

MICROFLUIDIC‐assisted 3d Printing Zinc Powder Anode with 2d Conductive MOF/MXene Heterostructures for High‐stable Zinc‐organic Battery

A Seamless Metal-Organic Framework Interphase with Boosted Zn2+Flux and Deposition Kinetics for Long-Living Rechargeable Zn Batteries

Helmholtz Plane Reconfiguration Enables Robust Zinc Metal Anode in Aqueous Zinc‐Ion Batteries

Multifunctional anchoring effect enables ultra-stable 3D-printed zinc powder-based anode

3D Cold‐Trap Environment Printing for Long‐Cycle Aqueous Zn‐Ion Batteries

3D Printing of MXene‐Enhanced Ferroelectric Polymer for Ultrastable Zinc Anodes

Ultra‐Stable 3D‐Printed Zn Powder‐Based Anode Coated with a Conformal Ion‐Conductive Layer

Heterostructured Interface Enables Uniform Zinc Deposition for High‐Performance Zinc‐Ion Batteries

Thickness‐Controlled Synthesis of Compact and Uniform MOF Protective Layer for Zinc Anode to Achieve 85% Zinc Utilization

3D Porous Copper Skeleton Supported Zinc Anode toward High Capacity and Long Cycle Life Zinc Ion Batteries

Encapsulation of Metallic Zn in a Hybrid MXene/Graphene Aerogel as a Stable Zn Anode for Foldable Zn‐Ion Batteries

Construction of ultrastable and high-rate performance zinc anode with three-dimensional porous structure and Schottky contact

Long lifespan and high-rate Zn anode boosted by 3D porous structure and conducting network

Establishing Thermal Infusion Method for Stable Zinc Metal Anodes in Aqueous Zinc‐Ion Batteries

Copper Hexacyanoferrate Solid‐State Electrolyte Protection Layer on Zn Metal Anode for High‐Performance Aqueous Zinc‐Ion Batteries

In‐situ Implanting 3D Carbon Network Reinforced Zinc Composite by Powder Metallurgy for Highly Reversible Zn‐based Battery Anodes

3D zincophilic micro-scaffold enables stable Zn deposition

<i>In Situ</i> Etching of Multifunctional Three-Dimensional Interfacial Layers for the Construction of Porous Zn Anodes with Enhanced Surface Textures

Regulated Ion/Electron-Conducting Interphase Enables Stable Zinc-Metal Anodes for Aqueous Zinc-Ions Batteries

Fast and Regulated Zinc Deposition in a Semiconductor Substrate toward High‐Performance Aqueous Rechargeable Batteries

Long-life and dendrite-free zinc metal anode enabled by a flexible, green and self-assembled zincophilic biomass engineered MXene based interface