Abstract:Magnesium has high strength to weight ratio , good machinability , high creep stress and high impact resistance . Such properties make the magnesium an excellent choice in many applications . Disadvantages of magnesium represented in low corrosion resistance in most environments and ignites easily in air . Surface modification techniques which are used to improve surface properities of Magnesium are conversion surface treatments like chromating , phosphating , galvanizing electroplating such as Cu , Zn , Ni , Cr , electroless metal plating and cladding by Aluminum foil . Anodizing in an electrolyte (with pH>12) is considered a passivation process that produces chemical stable protective oxide film on magnesium surface . Usually unsafe electrolytes such as KOH are frequently used . Anodizing of commercial magnesium (ASTM 9980A) was carried out in 3M KOH(unsafe) , 1M Na2SiO3 and 0.6M K2SiO3 (safe) electrolytes for time periods ranging from 10 to 50 minutes at constant voltage of 5V .The anode was magnesium specimen where the cathode was stainless steel type AISI 304 . Energy Dispersive X-Ray(EDX) and X Ray Diffraction (XRD) approved that magnesium Oxide (MgO) is the anodic film when using 3M potassium hydroxide electrolyte and a magnesium Silicate with a glassy morphology formed in the anodic film using safe electrolytes of 0.6M potassium silicate and 1M sodium silicate . Maximum film thickness reaches to 46 , 27,47 μm after anodizing at 30 min using 3M potassium hydroxide ,1M Sodium silicate , 0.6M Potassium Silicate respectively . It was found that the corrosion rate of commercially pure magnesium decreased from 37 to 7 , 2.2 , 1.3 mpy when using 3M potassium hydroxide , 1M sodium silicate , 0.6M potassium silicate respectively . At the same time the contact angle increases from 70 degrees to 114o , 105o , 113o degrees using the same electrolytes . An increase in microhardness of the anodic films was observed in 3M potassium hydroxide , 1M sodium silicate and 1M potassium silicate respectively . The adhesion of the anodic film measures according to ASTM D3359 method 13 for thickness <125 μm was classified in 3B which denote that the amount of the layer released by the adhesive tape lies from 5-15% of the formed layers using the three electrolytes.

Electrochemical evaluation of the anti-corrosion potential of selected amino acids on magnesium in aqueous sodium chloride solutions

Heterocyclic amino acids-based green and sustainable corrosion inhibitors: Adsorption, bonding and corrosion control

Computational, theoretical and experimental studies of four amino acids as corrosion inhibitors for brass in 3% NaCl medium

Exploration of natural polymers for use as green corrosion inhibitors for AZ31 magnesium alloy in saline environment

Study to amino acid-based inhibitors as an effective anti-corrosion material

Corrosion inhibition effect of several amino acids on an Al-Zn-Mg-Cu alloy: Electrochemical study, DFT and MD simulation

Anti-corrosion Investigation of Polylysine (Amino Acid Polymer) as Efficacious Corrosion Inhibitor for Al in Industrial Acidic Pickling Environment

Orange peel extracts as biodegradable corrosion inhibitor for magnesium alloy in NaCl solution: Experimental and theoretical studies

Synergistic inhibition effect of L-Phenylalanine and zinc salts on chloride-induced corrosion of magnesium alloy: Experimental and theoretical investigation

Corrosion inhibition of copper alloy of archaeological artifacts in chloride salt solution using Aloe vera green inhibitor

Concise Cu I -Catalyzed Azide–Alkyne 1,3-Dipolar Cycloaddition Reaction Ligation Remarkably Enhances the Corrosion Inhibitive Potency of Natural Amino Acids for Mild Steel in HCl

Cysteine as an Eco-Friendly Anticorrosion Inhibitor for Mild Steel in Various Acidic Solutions: Electrochemical, Adsorption, Surface Analysis, and Quantum Chemical Calculations

Recent Progress of Corrosion Prevention Method of Magnesium Alloy

The anti-corrosion performance of chaya leaf extracts on pure Mg substrates in Ringer ́s solution

Optimization of mild steel corrosion inhibition by water hyacinth and common reed extracts in acid media using factorial experimental design

Corrosion Inhibition of Magnesium by Anodizing in Safe and Unsafe Alkaline Electrolytes

Study the application of new type green corrosion inhibitors for iron metal

The Effect of Vanadate, Phosphate, Fluoride Compounds on the Aqueous Corrosion of Magnesium Alloy AZ31 in Dilute Chloride Solutions

Adsorbed film and synergistic effect of Benzyltriphenylphosphonium chloride and l-Histidine for magnesium alloys corrosion in NaCl

Corrosion Inhibition of Aluminum Alloy in 50% Ethylene Glycol Solution

Isatin Schiff bases: A green and sustainable Mg alloys corrosion inhibitor