Abstract:This study presents a novel combined generative shaping and material-forming (GSM) approach for preparing tritium breeder units for fusion reactors using 3D printing technology. For the first time, defect-free lithium-rich Li4SiO4 porous structures were successfully prepared by combining photopolymerization and reaction sintering processes based on the use of low-cost Li2CO3 and SiO2 ceramic powders. Investigation was conducted on the preparation of the ceramic powder-based mixture slurry as well as the photopolymerization 3D printing and reaction sintering processes. Li4SiO4-based porous lattice ceramics with high purity, no obvious defects, and adjustable packing fraction were fabricated. The mechanical properties of the samples prepared with different packing fractions were then evaluated. The prepared samples showed better mechanical properties than the pebble bed structures with similar packing fractions. At a packing fraction of 92.10%, the crushing strength and elastic modulus reached 186.49±0.04 MPa and 16.47±0.03 GPa, respectively. These results show that the combination of photopolymerization 3D printing and reaction sintering processes based on the use of low-cost ceramic powders has significant advantages in terms of flexibility and efficiency in structure design and fabrication and cost-effectiveness in material forming with enhanced performance, providing a promising route to produce high-performance tritium breeder structures for fusion technologies. In particular, the present combined method also paves a promising generalized way to enable effective generative structure-shaping and material-forming in the advanced ceramic manufacturing industry, not to mention that the preparation of high-performance Li4SiO4 tritium breeder units for fusion technologies.

Fabrication of hierarchical lattice structures from zirconia stabilized ceramics by micro-SLA 3D printing approach

3D printing of hollow lattice structures of ZrO2(3Y)/Al2O3 ceramics by vat photopolymerization: Process optimization, microstructure evolution and mechanical properties

Digital Light Processing 3D‐Printed Porous Yttria‐Stabilized Zirconia with High‐Thermal Shock Resistance

3D printing of dense structural ceramic microcomponents with low cost: Tailoring the sintering kinetics and the microstructure evolution

A new and simple way to prepare monolithic solid oxide fuel cell stack by stereolithography 3D printing technology using 8 mol% yttria stabilized zirconia photocurable slurry

Fused deposition fabrication of high-quality zirconia ceramics using granular feedstock

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

DLP 3D printing of scandia-stabilized zirconia ceramics

Additive manufacturing of interconnected hierarchically porous zirconia: Utilizing both microspherical and filamentary pore-forming agents via direct ink printing

Fabrication of High-Performance Al2O3-ZrO2 Composite by a Novel Approach That Integrates Stereolithography-Based 3D Printing and Liquid Precursor Infiltration

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

Three-dimensional printed yttria-stabilized zirconia self-supported electrolytes for solid oxide fuel cell applications

High Performance Solid Oxide Fuel Cells Based on Tri-Layer Yttria-Stabilized Zirconia by Low Temperature Sintering Process

Photopolymerization and reaction sintering enabled generative shaping and material-forming of complex ceramic structures with high performance

Additive manufacturing of 3D yttria-stabilized zirconia microarchitectures

Additive manufacturing of dense zirconia ceramics by fused deposition modeling via screw extrusion

A high-performance planar anode-supported solid oxide fuel cell with hierarchical porous structure through slurry-based three-dimensional printing

Fabrication of Complex-Shaped Zirconia Ceramic Parts Via a DLP-stereolithography-based 3D Printing Method

Layered Solid-Electrolyte Membranes Based on Zirconia: Production Technology

3D Printing of Robust 8YSZ Electrolytes with a Hyperfine Structure for Solid Oxide Fuel Cells